Foam Cutters: An Overview Of Electric Knives. How To Make An Electric Knife With Your Own Hands At Home From A Computer Power Supply?

Table of contents:

Video: Foam Cutters: An Overview Of Electric Knives. How To Make An Electric Knife With Your Own Hands At Home From A Computer Power Supply?

Video: Foam Cutters: An Overview Of Electric Knives. How To Make An Electric Knife With Your Own Hands At Home From A Computer Power Supply?
Video: Foam cutter - How to make it the easy way! 2024, March
Foam Cutters: An Overview Of Electric Knives. How To Make An Electric Knife With Your Own Hands At Home From A Computer Power Supply?
Foam Cutters: An Overview Of Electric Knives. How To Make An Electric Knife With Your Own Hands At Home From A Computer Power Supply?
Anonim

Styrofoam can be safely called a universal material, since it is widely used in a wide variety of industries: from construction to making crafts. It is lightweight, inexpensive, and has many benefits. There is only one drawback - the material is quite difficult to cut. If you do this with an ordinary knife, then in most cases the foam begins to break and crumble. To prevent this from happening, it is necessary to use special cutters. They come in different types. You can buy a cutter in construction equipment stores or make it yourself, having all the necessary materials and accessories at hand.

Image
Image
Image
Image

general description

A foam cutter is a special device that allows you to separate the required amount of material from the general plate. But here it is important to consider how exactly and for what purpose the foam is cut. Already on this basis, you need to decide on the choice of cutting tool.

It is permissible to use both store and homemade options. The most important rule is that the torch does its job well.

Image
Image

Overview of Views by Cut Type

There are several types of cutting foam. For that so that each time the process is easy, and the result is positive, it is necessary to determine in a timely manner the type of tool that will be used during the work . It is possible that you will have to use two types of torches at a time. It all depends on the tasks set.

Image
Image
Image
Image

For linear

Linear cutting of foam is considered to be the simplest of all available. It is very often used when polystyrene is needed to insulate a room, as well as when carrying out other identical construction work . Accuracy and accuracy are not very important here. The most important condition is that the foam itself does not break. For this case, hand tools are quite suitable: a knife, a hacksaw or a metal string.

Image
Image

The knife is most suitable for cutting foam, the width of which does not exceed 50 mm. The hacksaw, in turn, will cope with thicker plates (up to 250 mm). Of course, in both cases, the foam particles will fall out, and the cut will not be perfectly even. But the material will remain intact.

Also, metal strings are often used to cut foam . You don't have to buy new ones for this. Those that have already been used for their intended purpose will do quite well.

Image
Image
Image
Image

For that To make the string as suitable for cutting as possible, you need to tie it to both ends with a wooden or plastic handle . The cutting process will be exactly the same as when working with a two-handed saw. If the width of the foam is large enough, then it will be more convenient to cut it together. In this case, in any case, the foam must be securely fixed.

An important point: when cutting foam, it is recommended to use special protective headphones or earplugs, since the sound is rather unpleasant during operation.

To make the cutting process easier, it is advisable to pre-lubricate the tools with machine oil.

Image
Image

For curly

Curly carving is considered more complex when compared with the previous version. That is why all of the above tools are not suitable for this purpose. But others can be used here.

A good option is an electric knife . Such a device is able to cope with material, the thickness of which does not exceed 50 mm. In order to cut the desired piece, it is required to hold the knife along the outlined lines at an average speed.

Image
Image

Do not do this too slowly, as this will cause the material to melt at the cut points. Too fast and abrupt movements can lead to crumbling and even breaking of the material.

If the foam board will have a thickness of more than 50 mm, then a heat knife can also be used . True, you will have to cut on both sides, each time deepening the working blade only half. It is noteworthy that the heat knife can be powered by mains or batteries.

Image
Image
Image
Image

With metal plate

A metal plate cutter can be used as an additional tool. It is not very easy to get it in the store, but you can make it yourself from an old, but working soldering iron.

The manufacturing process is quite simple, since it consists only in replacing the old tip with a new metal plate . Better to use a copper plate. You can take steel, but this material, due to its properties, heats up much longer and is difficult to sharpen.

Image
Image

The plate must be sharpened on one side, and after that the device is ready for use as intended.

How to do it yourself?

An old soldering iron or burner will make a good option. To make such a cutter at home, even special knowledge is not required.

A stationary cutter can also be made at home. To do this, you need a power supply from your old computer. Before you start manufacturing, you need to prepare all the necessary materials:

  • power supply (the one with an additional on / off button on the case is better suited);
  • adapter with SATA-connector;
  • copper wire (can be taken from an old charger);
  • clip;
  • nichrome thread.
Image
Image
Image
Image

Initially, you need to prepare the most important part - the power supply from the old computer . There is a very important point to consider here. The fact is that the power supply itself does not turn on without the participation of the motherboard. In order for the created tool to work, you need to short-circuit the power on the green and black wires. You can use a prepared paper clip or take a small piece of wire.

Image
Image
Image
Image

To warm up the nichrome thread, you will need to take power from yellow and black wires. A two-wire cable must be connected to them.

A nichrome thread should be connected to the back of this wire. There is no need to solder or fix the thread in any other way. To facilitate the work, it is enough to clamp them together with a small piece of copper wire. The braid must be removed from the cable. This is necessary so that during cutting it is possible to stretch the nichrome thread in different directions.

It is interesting that in this cutter it is possible to control the heating temperature of the nichrome filament . When it is shortened, the temperature rises and, accordingly, with increasing length, the temperature decreases.

Image
Image
Image
Image

The homemade foam cutter is ready. The scheme of its work is quite simple . The free edge of nichrome must be clamped and pulled so that the thread itself turns into an even and elastic line. The power supply is connected to the network. The second contact should touch the nichrome thread. The distance between the contacts should be about 50 cm.

In order to warm up the thread to the required temperature, you need to move the contact along its entire length . And when the heating is done, you can clamp the second contact on the nichrome. The device is now fully operational. In principle, this cutter is very similar to a string cutter. Only, unlike the manual version, this one works much faster.

Image
Image

In the process of work, it is important to ensure that no overlaps form on the nichrome thread. The fact is that this way you can burn yourself, spoil the material being processed, and also the power supply can burn out from overvoltage.

For cutting foam, any of the above purchased or homemade options will work . The most important thing is to initially decide on the required type of cutting. It is also important that the material itself is of good quality, as old foam or one that has been stored under improper conditions in the past will crumble anyway.

Recommended: