Do-it-yourself Wooden Lathing For Siding: The Dimensions Of The Lathing For Vinyl Siding. How To Fix It?

2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-07 13:49

Vinyl siding is an affordable material to cover your home, make it beautiful and protect it from external factors (sunlight, rain and snow). It is required to provide air flow from the bottom, exit from the top. To install the siding, a crate is made. Do-it-yourself wood lathing is not difficult.

Peculiarities

The frame of the lathing on the house is installed to solve the following tasks:

• remove the unevenness of the walls;
• take into account the shrinkage of the house;
• insulate the house;
• provide ventilation of the facade and insulation;
• ensure an even distribution of the load.

It is important to remember that during installation it is necessary to provide for a ventilation gap of 30-50 mm between the siding and the load-bearing wall or insulation. It is undesirable to use a wooden beam in places of contact with moisture, since with a frequent cycle of wetting and drying, the wood quickly collapses.

It is not recommended to make a crate in the basement part of wood

If we install vinyl siding horizontally, then the fixing bar is attached vertically. Installation of vertical siding is common, but much less common.

What should be the step?

When installing horizontal siding, the distance between the vertical slats should be between 200 and 400 mm. If you have winds, then the distance can be made closer to 200 mm. At the same distance, we attach the bars to the wall, on which we will attach the slats . When installing vertical siding, it is the same. We select the sizes ourselves from the proposed ones.

What is required?

To install the lathing you will need:

• portable circular saw;
• hacksaw for metal;
• cross saw;
• cutter knife;
• roulette;
• rope level;
• metal carpentry hammer;
• level;
• pliers and crimping pliers;
• screwdriver or hammer with a nailer.

We prepare a wooden bar

The calculation of the quantity depends on the chosen installation distances of the timber, the number of windows, doors, protrusions.

Let's talk in more detail about the choice of size and material

Wood lathing is mainly used for finishing dilapidated or wooden houses, brick - less often. Timber frames are more commonly used to install vinyl siding. The cross-section of the bars can be different: 30x40, 50x60 mm.

With a large gap between the wall and the finish, a beam with a thickness of 50x75 or 50x100 mm is used . And for insulation, you can use a rail for the thickness of the insulation itself.

The use of a raw timber of a larger size can lead to deformation of the entire structure.

The selected timber must be able to withstand the siding. It must be dried, the length and cross-section must correspond to the documents, even, as few knots as possible, no traces of mold . Preference should be given to wood species that are resistant to moisture, such as larch. Dry planed timber does not lead or twist, the siding will lie flat on it.

The length of the timber must match the dimensions of the wall . If they are short, you will have to dock them.

We prepare fasteners

Purchase self-tapping screws with the appropriate length or dowels if you need to fasten the battens to a concrete or brick wall. It is required to prepare wooden blocks for mounting to the wall of the house.

How to do it?

It is necessary to remove all unnecessary things from the house: ebb tides, window sills, old finishes. We set marks with a plumb line with a nylon rope and a level.

Determine the distance from the wall to the future crate . We nail (fasten) the bars to the wooden wall. And also brackets are used (suspensions from galvanized metal 0, 9 mm). The lathing is installed on these brackets or bars.

We outline the places for drilling, if it is a brick wall, or the places for fixing the bars, if it is wooden. We fasten to the brick through plastic dowels, and to the wooden one - with self-tapping screws.

We measure the interval from the fixed bar, for example 40 cm, it is no longer necessary, and we fix it . The wall must be treated with a deep penetration primer.

When using wooden battens, processing of the lathing with fire-retardant impregnation is required. The moisture content of the wood should not be more than 15-20%.

Lathing with insulation

If the insulation is laid, then the timber must correspond to the thickness of the insulation.

Insulation polystyrene foam, mineral wool can be laid, while the wool is covered with a vapor barrier film, for example, Megaizol B . The film protects the mineral wool from moisture, we fix it and wrap it to the window. Vapor-permeable wind and moisture protection film (megaizol A).

It is required to measure the installation site of the horizontal batten with insulation where the window sills will be installed . Next, we set a horizontal bar above the window, above the window, to the left and right of the window, that is, we frame the window. We wrap the film in a niche around the window.

Lathing without insulation

It's easier here, you just need to remember to process the walls and crate, maintain the size of the ventilation gap

Log houses have crowns. Two options: bypass the crowns or remove.

The first option is more costly - it is necessary to additionally sheathe and revet all the protrusions . The second will visually expand the house, while the crowns will need to be sawed off.

How to fix the siding?

To install siding, use:

• galvanized self-tapping screws;
• aluminum self-tapping screws (press washers);
• galvanized nails with large heads.

We fasten it with a press washer at least 3 cm. Do not tighten it all the way to allow the siding to move.

When screwing in the screw, a gap is formed between the screw head and the vinyl panel . It should be 1.5-2 mm. This allows the siding to move freely as it expands or contracts with temperature fluctuations without warping the siding. Self-tapping screws must be screwed into the middle of the oblong hole. It is necessary to screw in the screws in increments of 30-40 cm. After screwing all the screws into the panel, it should move freely in different directions by the size of these holes.

We maintain the step of fasteners for panels of 0, 4-0, 45 cm, for additional parts at 0.2 cm

If you correctly calculated and assembled the crate, it will be easy to hang the siding. The safety of the walls of the building is guaranteed, and the house will shine with new colors.