Cut-in Profiles For LED Strips: Recessed Aluminum Light Profiles For Plasterboard Walls And Other Recessed Lighting Profiles

2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-15 04:10

Profiles for LED strips are different. These important parts differ in many ways, including the way they are fastened. There is a category of cut-in profiles. They will be discussed in today's article.

Features and Applications

Nowadays, LED lighting is one of the most popular. This type of lighting fixture can be seen in many homes today . Diode tapes are in great demand. They both look beautiful and are installed on a variety of substrates - from floor to ceiling. True, the installation of such products turns out to be difficult if there is no special profile.

The profile parts allow the diode strip to be mounted on a wide variety of surfaces . There are several varieties of these mounting parts. There are both standard overhead or corner, and built-in subspecies. The latter are popular. They are installed in different rooms - in the kitchen, in the living room, and in other rooms. Installation work is relatively straightforward and not time consuming. Almost every user can cope with the installation of a cut-in profile.

Cut-in profiles are made from different materials . They are available in different sizes. It is noteworthy that most of these products correspond to the dimensions of the LED strip, so it is extremely rare to adjust these parts to each other.

There are other important features of the products under consideration

• Cut-in models of profiles are characterized by low weight. And also they are distinguished by very good technical characteristics. Due to these features, users have every chance of encountering their convenient and practical application.
• As mentioned earlier, such products are easy to install. During their operation, there are also no special difficulties.
• Most of the cut-in profiles are made from sturdy and practical materials. Thanks to this, the designs demonstrate a long service life and high wear resistance.
• Ready-made mortise systems have an attractive appearance. It is often because of this characteristic that users prefer these types of profiles.

It should be borne in mind that mortise elements are usually installed on bases made of plasterboard or chipboard.

Thanks to the cut-in type profiles, the installation of LED strips is much easier and takes little time . As a result, both the backlight and the base it sits on look neat and attractive. Often, the lighting system in question is installed as a backlight for shop windows or office environments.

Views

Mortise profiles designed to accommodate strips with LED bulbs are different. Similar products can be selected for a variety of installation conditions. We will find out by what criteria the considered structures are classified, and what parameters they have.

All cut-in profiles are divided according to the material from which they are made. The following most popular varieties are produced today.

Aluminum . Some of the most requested options. Practical, durable, wear-resistant. They do not undergo rust formation, do not deform, but at the same time remain sufficiently flexible. They look attractive and can be colored if desired by users. Installation of aluminum profiles is quick and easy.

Plastic . This refers to profiles made of polycarbonate. It is an inexpensive, practical material. It is flexible, easy to install. It is lightweight, differs in textures and shapes. Polycarbonate products are not anodized, unlike aluminum ones. Due to this, the strength indicators of such products are higher.

The built-in profile is divided not only by materials of manufacture, but also by shapes. Today, products are produced with the following types of structures:

standard square;

rounded;

trapezoidal

tapered profiles.

The most practical are the profiles, in the design of which a special diffusing element is provided . The latter can be matte or crystal clear. Depending on the structure of the diffuser, the degree of saturation and brightness of the diode lighting can be higher or lower.

Cut-in profiles with or without a screen can be installed on different fasteners. Most often these are plastic parts that are white or black.

Mortise products are produced with different dimensional parameters . For example, on sale you can find models with an upper edge width of 22 mm, an inner edge width of 11.2 mm, and a depth of 6 mm. Instances with a screen can be 30 by 30, 34 by 12 mm - there are a lot of options. The parameters of the widest options usually reach 12 and 13 mm.

The length of the cut-in profiles also varies. On sale, products with a length of 2 m are more common. Most of the copies are initially adjusted to the parameters of LED strips.

Installation technology

Installation of cut-in profiles does not require a lot of effort and free time. Carrying out installation work does not cause any special difficulties for the craftsmen. Almost every user can cope with all stages.

The recessed profile can be installed both in the wall and in the ceiling and even in the floor base. It all depends on where exactly it is planned to equip high-quality and beautiful lighting. Let's consider in detail the technology of mounting a profile for a light strip with diodes.

• The first thing the master will need to do is to choose the place where the profile for the light strip will be embedded. You should think about this issue in advance, since in the future it will be necessary to make a groove in the selected base.
• Having chosen the installation location, it is necessary to make a groove in it. It is necessary to form the groove connection so that its dimensional indicators correspond to the parameters of the tape with the profile.
• At the place of installation of the part, it will be necessary to mark the area for fixing the profile. It is imperative to determine the place of the beginning and end of the lighting device. The places where the fasteners will be located should also be noted.
• The profile fixing points will need to be drilled out. For these purposes, it is advisable to use a drill with a diameter that matches the diameter of the fasteners. These can be screws or bolts.
• According to the specified marks, it will be necessary to trim the profile, if necessary.
• If you are installing an aluminum model, then you will also need to make mounting holes in it. Their locations must match the locations that you prepared on the base.
• The cut-in structure will need to be inserted into the groove made at the very beginning of the work. After that, you can additionally fix the structure with bolts or self-tapping screws using a screwdriver.

The profile must fit tightly and securely into the grooves. If the notch was originally made end-to-end, it is advisable to insert the base under the tape into it using a special rubber mallet.

Having installed the profile, you can proceed to fixing the LED strip itself.

General recommendations

When the selection and installation of cut-in profiles is planned, it makes sense to build on some useful recommendations on these issues

• If you want the diode lighting in the cut-in profile to be more subdued, it makes sense to choose a base with a matte screen.
• When choosing profiles of cut-in type, it is very important to pay attention to their dimensions. The length and width of such parts varies. In order not to be mistaken with the choice, you should first measure the parameters of the LED strip.
• It is recommended to install the cut-in profiles in such a way that subsequently users have free and unhindered access to the diode tape that is fixed in them.
• Inexpensive polycarbonate profiles are presented in different colors. They can be selected based on the color of the plaster or paint that is applied on the base.
• Installation of a cut-in profile, like any other, should be carried out as carefully as possible. The fact is that a carelessly installed diode tape immediately catches the eye - such interior elements look ugly.
• If the installation of a profile made of aluminum is planned, then its edges must be protected from burrs even before starting work.
• Recessed profile models are strongly not recommended to be installed in areas that are exposed to serious and regular loads. That is why such products are recommended to be mounted in chipboard or gypsum board bases.

Also pay attention to the following nuances

• It is recommended to connect diode strips using a parallel method. Due to this mounting technology, it is possible to prevent unnecessary voltage loads during the operation of the lighting device.
• When choosing a cut-in profile of any modification, it is very important to ensure that it does not have a single drawback. Any damage, deformation, breakage and shortcomings are unacceptable. Poor quality LED strip fasteners will prove to be a short-lived solution.
• A profile for a tape with diode lamps is allowed to be installed not only inside the dwelling, but also outside it. Most of these options are made moisture resistant, therefore, under the influence of atmospheric precipitation, they will not collapse and deform.
• If you want to pick up such a box that you don't have to worry about breaking during the installation process, then it is better to choose a model made of aluminum. Such specimens are most often bought for installation in wall or ceiling surfaces. And also aluminum profiles are suitable for embedding in stairs and floor coverings.