The Washing Machine Flows From The Bottom: Reasons - Water Flowed Out During Spinning During Washing And When Dialing During Rinsing

2024 Author: Beatrice Philips | [email protected]. Last modified: 2023-12-16 05:33

Water leaks from under the washing machine are simply obliged to alert. As a rule, if water forms on the floor next to the washing device, and it poured out from it, then you should look for and fix the breakdown immediately. It should be borne in mind that leaks can lead to more serious consequences in the form of flooding of neighbors and damage to furniture.

What's the first thing to do?

Modern manufacturers of washing devices often equip their products with a leakage protection system. This allows you to shut off the water supply to the machine when a malfunction occurs, which will prevent flooding. Water leaks from the machine are quite common malfunctions among many models of washing equipment.

If it becomes noticeable that the washing machine has leaked, it is important not to enter the puddle that has formed, or to start wiping it up right away. The first thing to do is to disconnect the device from the mains. As long as the machine remains plugged in, it is life-threatening for those nearby.

The second action, if water flows out during washing, is to shut off the tap through which liquid is supplied from the water supply to the equipment. To do this, simply turn the desired tap to the closed position.

When both steps have been completed, you can drain the water that remains in the machine . This is possible with an emergency drain connection. It is a small hose with a plug at the end, which is located behind a separate door near the drain filter.

If the model does not have an emergency hose, then the water can always be drained using the filter hole. It is located on the front panel. At the last stage, you need to get all the things out of the drum . Only after all the above steps can you proceed to the inspection and find out why the washing machine is leaking.

Causes of malfunction

Most often, the washing unit leaks if the operating rules have been violated. Often, water runs out due to washing with products that are not suitable for this type of machine or washing mode. As well as Damage to the drain pump is a common cause.

Somewhat less often, leaks occur as a result of defective parts or poor-quality assembly of units.

Inlet or drain hose

The search for breakdowns should begin with the hoses through which the water is supplied and drained. It is important to inspect them along their entire length . Longitudinal cracks and most other damage are immediately visible. They can be formed simply by rearranging furniture. Indeed, under such circumstances, the hose can be very kinked or too stretched.

If a puddle near the machine forms while drawing water, and the hoses seem to be intact, then you should check them more carefully. To do this, they must be disconnected from the device and plugs must be placed on one side. After that, along the entire length of the hose, you need to wind up toilet paper and fill it with water. If the hose leaks somewhere, then wet traces will appear on the paper.

Also, problems can arise due to poor connection of the inlet hose and the union .… If the inspection of the hoses shows that they are completely intact, then they should be carefully connected to the washing device.

Powder dispenser

If the machine leaks, but the leak is insignificant (for example, water just drips), then you should look for the reason in the detergent tray. In the process of washing, substances are washed out of it with water. but sometimes powder or other substance may remain due to incomplete dissolution in the tray and a blockage occurs . In this case, the water does not pass quickly through the dispenser, so some of it gets out.

If, upon inspection, almost all the holes were clogged in the tray, then the reason for the running water is precisely here.

Pipe branch

The filler neck can cause the machine. This is due to the influence of vibration from the machine during the rotation of the drum. Most often, this leads to the fact that the junction of the filler pipe with the tank weakens or even collapses.

The filler valve branch pipe can also leak if its integrity or tightness of the connections is broken . You can see this after removing the top cover from the washing device. It is under it that this detail is located.

A few months after the start of the operation of the washing equipment, the drain pipe may leak .… This is either due to excessive vibration of the washing machine, destroying the joints, or as a result of a poor connection between the pump and the tank.

The malfunction can be detected and eliminated if the washing device is positioned so that it is possible to reach the drain path, which is located at the very bottom of the machine from the back wall (put horizontally on its side).

Door cuff

Negligent use of the washing machine can lead to failure of the cuff on the hatch door. This will be especially clearly seen when rinsing or spinning, as the leak will be from under the door of the machine. Leakage is possible even with minor damage to the cuff.

Tank

If the tub is damaged, the washing device flows from below. Such the most important structural element can only fail due to improper operation of the unit . You can identify a breakdown if you put the machine on its side, and then carefully examine its bottom. At the same time, it is advisable to highlight with a flashlight. The location of the damage will be visible on the traces of the water. In addition to cracks in the plastic part of the tank, leaks can occur due to a faulty rubber gasket that connects its parts.

In any case, it is best to consult a professional about a faulty tank.

Deformation of the stuffing box

Another part of the washing machine, which is often the reason for the fact that water pours on the floor, can be the oil seal. This element protects the bearings from water ingress. With long-term operation, the gland loses its elasticity, deforms, and seal leaks appear . In these cases, the liquid penetrates to the bearings, and through them to the outside of the device.

How to fix it?

Knowing the cause of a washing machine leak, you can often fix it yourself. For example, if the problem is in the drain hose, then such a malfunction can be temporarily eliminated using the most common insulating tape . In the drain system, the fluid pressure is quite low, so the damage wrapped with electrical tape will allow you to do a couple more washes. However, in the end, you will have to buy a new hose and change the leaky one.

As for the leaky hoses and pipes located inside the device, they only need a complete replacement . But if the cause is connections, then the leak is eliminated quite simply. It is enough to coat the junction with rubber glue and wait for it to dry completely (about 20 minutes). But for the duration of drying, it is advisable to tightly squeeze the junction.

The drain filter is also easy to change. You need to unscrew it from the neck. After that, inspect the thread and make sure that there is no dirt and dried salt deposits on it. After cleaning, fit a new filter and tighten the cap carefully to make it fit as tightly as possible.

A leaking machine door indicates damage to the cuff . Minor cracks can be repaired with waterproof adhesive and an elastic patch. To do this, remove the seal by first removing the clamp holding it in the hole. When installing the restored cuff, it is advisable to make it so that it is on top of the hatch. So the load on it will be minimal.

If this repair fails, a new cuff should be fitted. This is quite difficult, so it is better to use the help of a specialist.

The metal tank consists of two parts with a rubber gasket between them. If there is a malfunction in it, then the gasket is changed to a new one. If cracks are found in the plastic, they are repaired with a polyurethane sealant . Of course, if they are large or located in places that are difficult to reach, then it will be necessary to disassemble the washing unit. However, it is better to entrust the leak from the tank to professionals, since the problem can be more global, up to replacing the tank. Sometimes it is more profitable to buy a new washing unit than to replace the tank.

If water leaks due to worn oil seals, then the bearings will have to be changed, because the wear of these parts leads to the fact that water begins to seep through the bearing assembly. To eliminate it, you need to remove the back cover, get out the old bearings with oil seals and install new ones.

It should be clarified that the formed scale on the heating element in the washing device cannot cause a leak. This is only possible in cases where the heating element explodes and burns through the tank. However, this happens quite rarely.

Practice shows that you can cope with any problem, if not on your own, then with the help of specialists . It is important to remember that the response to a fault must be very quick. Otherwise, a small breakdown can lead to more serious consequences.

Prophylaxis

Household appliances require proper operation, otherwise their service life will be significantly reduced. There are a number of guidelines to follow to avoid leaks . For example, before loading clothes into the drum, it is important to inspect them for metal elements. If there are any, then you need to wash things in a special cloth bag. The same should be done with small things that can get into the drain pipe of the unit.

Before closing the main cover of the washing machine, check how tightly the drum is closed. This is important for models with vertical loading. This tip will help prevent water from spilling out during spinning.

Besides, at the end of the wash, do not forget to disconnect the washing equipment from the power supply . This is due to the fact that power surges can lead to breakdowns. It is best to install the machine in places where the humidity is the lowest. For example, the kitchen would be a good place for a washing machine.

In order for the service life of the machine to be long, you should not overload it with things. Overloading can lead to leakage during spin mode . Poor-quality water in the plumbing also causes breakdowns. Therefore, it is better to install a filter in the system in advance. And also in order to avoid leaks, it is important to use only high-quality detergents.

To prevent malfunctioning of the tank, carefully check all pockets before putting clothes in it for washing. It is especially important to check children's and work clothes for sharp or metal objects.

Do not leave the washing unit idle for a long time . It should be clarified that downtime has a negative impact on rubber parts, impairing their elasticity and strength. It is not uncommon for leaks to occur when washing after a standstill. Periodic cleaning of the drain tube can prevent leaks. It may contain buttons, pins, coins, hairpins, toothpicks, bra bones.