The First Start Of The Washing Machine: How To Correctly Start The First Wash Without Laundry In A New Automatic Machine? Recommendations

2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-18 12:09

The first start-up of the washing machine is a crucial, important stage that determines how successfully the further operation of the equipment will proceed. Each manufacturer in the instructions gives useful recommendations that allow even an inexperienced user to understand all the complexities of this procedure. When studying how to correctly start washing without laundry for the first time in a new automatic machine, you should pay special attention to the choice of detergents, follow the step-by-step action plan exactly.

Preliminary procedures

In order for the first start-up of the washing machine to take place, you need to properly prepare the unit. Regardless of the model and brand, the preliminary stage is the same for all types of such equipment. Before you start washing in a new machine without laundry, you need to make sure that the equipment is ready for it.

Automatic equipment in its modern design has a special mode in which its self-cleaning and starting start-up are performed.

Checking the readiness of equipment is an important step that cannot be neglected. It includes several steps.

• Careful study of the instructions . Although the general rules are always the same, some manufacturers provide additional recommendations for starting the machine in self-cleaning mode. It is best not to ignore these tips and follow the instructions exactly when you first choose the type of wash.
• Checking the reliability of the fastening of the hoses . They should be tightly crimped with clamps and well secured. A hose that has jumped off during the operation of the equipment can create conditions for a local communal accident. Poor fastening is especially dangerous in a situation where the machine vibrates strongly during operation.
• Installation of plugs . They are included in the scope of delivery and are placed in place of the transit bolts. Such compensating elements make it possible to avoid deformation of the technological holes during the operation of the equipment. It is important to make sure that all fasteners are removed - depending on the model, there may be 4 or 6 shipping bolts in the washing machine.
• Opening the water shut-off valve . It is located on the inlet hose. After using the machine, the water supply is always shut off.
• Checking the case for traces of adhesive tape and other packaging … If they are found, it is imperative to remove the excess fasteners holding the parts. They can interfere with the normal operation of the washing machine.
• Study of the inner space of the drum . It can get solid objects, poorly fixed fasteners, flying off during transportation. If such foreign inclusions are found, they must be removed.

All these steps are performed before the machine is powered up. If the device has been outdoors for a long time at a low temperature, it should take from 4 to 8 hours before it is connected and started.

Step-by-step instruction

Starting your washing machine correctly the first time is fairly easy. It is only important to follow certain step-by-step instructions that ensure the safe preparation of equipment for full operation.

• The electrical appliance installed on site is connected to the network . A corresponding indication should appear on the dashboard. Sometimes it occurs with a slight delay - this must be taken into account.
• The loading door of the device closes tightly … A characteristic click should be heard, indicating the operation of the lock.
• The detergent drawer on the front panel slides out … The starting composition or the usual SMS for automatic machines is poured into the powder compartment. It is important to keep track of dosage recommendations and not confuse compartments. The filled tray is pushed into the inside of the washing unit.
• If there is an auto-cleaning function in the car - press the corresponding button (the number of times is indicated in the instructions). If not, the first wash is performed in the Cotton mode at a temperature of 60 degrees. It starts, water should be poured into the drum. The average test wash duration is about 70 minutes.
• Control the operation of the equipment . The engine should work evenly, without a sharp squeal, the appearance of extraneous grinding, knocking. Vibration can be caused by incorrect positioning of the washing machine. If it appears, it is recommended to pay attention to how smoothly its body is installed, whether there is any contact with the wall, pieces of furniture.
• At the end of the wash cycle, wait until the water is completely drained and the door unlocked . This may take time - usually no more than 2-3 minutes.
• Inspect all parts and connections . Particular attention is paid to the drum compartment, the condition of the legs. You need to carefully examine the floor for leaks. Check the tightness of the hoses to the surface of the connections.
• Open the door, leave it in this position for 2-4 hours to evaporate excess moisture . If you close the hatch earlier, mold and an unpleasant odor may appear inside the case.

Features of the choice of detergents

There are certain guidelines for choosing synthetic detergents for the first wash cycle. Of course, you can also use a conventional powder, which has a corresponding mark on the package. The presence of the inscription "machine" will allow you to understand that the choice was made correctly . However, there are also specialized formulations focused specifically on the removal of technical contaminants. They eliminate the smell of machine oil and other lubricants, thoroughly wash out fatty components from equipment parts.

Among the most famous compositions are Helfer Start , suitable not only for the first start-up, but also for regular maintenance of the internal parts of the unit. The surfactants used in the composition of the agent have an intense degreasing, cleaning effect, break down lime deposits that arise during the operation of the equipment.

It is important to remember that the dosage of powder for the first wash should be significantly less than with a standard load of equipment . Most manufacturers recommend taking 10% of the usual SMS volume. It should be added that in this case, the amount of powder set to remove heavy dirt is used as a reference measure.

If you do not want to carefully calculate the volume of SMS, pills can be used . They are produced by the Oro company, in a package of 2 components. The first tablet - Clean, is designed to combat factory pollution. After 30 wash cycles, descale with a second Calc pill.

Important nuances

There are a number of things to consider when planning your first wash in a new washing machine after purchase. As soon as the device is delivered, it is carefully examined, the completeness of the equipment is checked. The removed packaging and transport fasteners do not need to be thrown away - they are stored during the warranty period, since some manufacturers indicate this point in their requirements. Before installing the machine, make sure once again that there are no cardboard or other packing materials left on the bottom side and that the shipping screws have been removed from the rear wall.

Before starting for the first time, it is important to carefully check the correct positioning of the equipment . It should not come into contact with walls or furnishings. In addition, the roll of the case should not exceed 2 degrees, otherwise strong vibration will be felt during the operation of the equipment. Next, the hoses for water supply and drainage are connected.

It is strictly forbidden to put laundry in the tub during the first wash . This procedure is necessary to clean the interior of the unit from traces of grease and other technical fluids, specific contaminants. Washing is carried out exclusively with the hatch door tightly closed. It is preliminarily recommended to check the permeability of the sewer drain. If it is clogged, the machine will not be able to discharge the water as needed.

When extraneous sounds appear during the first wash: knocking, grinding, an error signal appears on the display, you need to stop the process according to the scheme indicated in the instructions . You can contact the specialists of the service center for an emergency consultation.

If the start-up of equipment causes a spontaneous power outage, you need to revise the connection diagram, temporarily disconnect other devices from the network. A blown fuse indicates an overload in the network.