2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-09 13:15
Polycarbonate is a modern good material. It bends, it is easy to cut and glue it, it is possible to create a structure of the required shape from it. But over time, water and dirt begin to accumulate in its cells, insects hide there for the winter, which leads to damage to the material and destruction of the structure. Therefore, quite often the question arises of how and how you can glue the ends of polycarbonate with high quality.
How can you glue?
Polycarbonate has appeared relatively recently, but has already become popular due to its durability, resistance to different weather conditions. It transmits and scatters sunlight well, retains heat in a closed structure . Sheds and canopies of buildings are made of cellular polycarbonate, greenhouses and gazebos are erected. In this case, it is imperative to close the ends of the product so that it lasts a long time.
Some people try to do this with scotch tape . Of course, such material will be cheap, but it will provide protection for a maximum of a year, then it will begin to tear. Therefore, you need to use materials specifically designed to seal open polycarbonate cells. There are different means to solve the problem.
For example, a rubber face seal can be used . It has a low price, is easy to use, and helps to reduce the vibration of polycarbonate in the wind.
However, over time, the rubber seal undergoes deformation, it is characterized by a loss of elasticity, it becomes brittle, and it hardens in the cold.
You can glue the ends with special tapes. Their purpose is to protect cellular polycarbonate from factors destroying it. The product has an almost unlimited service life, it is not afraid of mechanical damage, moisture, temperature extremes. The upper layer of the tape plays a sealing role, the inner layer is covered with high-quality durable glue.
There are 2 types of tapes:
- perforated;
- sealing solid.
When erecting a structure, both types will be needed, since they are used in different ways and have different functions. The sealant is glued to those ends that are at the top of the structure. It prevents debris, precipitation, insects from entering the building material.
Perforated is applied to the bottom ends, it has an air filter. The main task of such a tape is to remove moisture that accumulates in the honeycomb during the operation of polycarbonate.
Also, an effective way would be to use end profiles . They need to be put on the edge of the canvas. The end profile will reliably protect the honeycomb, will create a frame for flexible polycarbonate sheets, and will give a more aesthetic appearance to the structure.
To ensure the stability of the structure, you will need to seal the places where the polycarbonate panels are connected. This can be done with a silicone sealant.
Embedding scheme
It is quite possible to do the processing of the ends with your own hands. To solder the edges with the tape yourself, you only need a tool to cut the tape - a knife or scissors. It is also advisable to have a stitching roller on hand. You need to attach the tape correctly, so follow the step-by-step instructions.
- Prepare the butt. Remove all burrs, dirt from it, it must be clean and dry. And also you need to degrease the surface.
- Take measurements and cut the tape to the required length. Remove the protective strip from it.
- Now you need to carefully attach the tape to the end. Make sure that the middle of it can then be laid on the end.
- Smooth the tape well to avoid bubbles and unevenness.
- Bend the tape and close it with the middle of the end, iron it well with ironing movements.
- Bend the tape again and cover the other side of the sheet. Iron. Use a roller to create a smooth and even attachment of the tape to the sheet.
Recommendations
In order for the structure to serve for a long time, use the following recommendations
- Before sealing the ends, it is imperative to remove the remnants of the protective film and glue from the polycarbonate sheet.
- When gluing the tape, do not wrinkle or wrinkle it, and do not pull it too tightly. Use only punched tape if the structure is arched.
- For greater reliability, use end profiles over the tape. Match them to the color of the canvas.
- If you urgently need to seal the ends, but there is no tape, use construction tape. However, do not forget that it is only a temporary solution.
Recommended:
Foam Glue: With What Solvent To Dissolve The Foam To A Liquid State? How To Make Glue With Acetone And Gasoline With Your Own Hands? Using Homemade Glue
Advantages and disadvantages of foam glue. What solvent can be used to dissolve the foam to a liquid state? How to properly make foam glue using gasoline? Where is the composition used?
Rubber Glue: How To Choose For Rubber, Rubber Compound For Gluing, Grades 88 N And CA, The Best Waterproof Quick-drying Glue
Rubber glue is very popular both in industry and in everyday life due to its excellent characteristics. How to choose the most suitable rubber bonding compound for rubber? How do 88 N and CA brands differ from other rubber adhesives and what are their advantages?
How To Glue PVC Panels In The Bathroom? How To Glue Plastic Structures, How To Glue It Correctly, How To Glue Sheet Options, How To Glue A Room
How to glue PVC panels in the bathroom yourself? How to glue plastic structures yourself at home? How to properly glue PVC panels in the bathroom with your own hands?
Polycarbonate Glue: How To Glue Transparent Polycarbonate To Each Other Or To Metal? How Can You Glue It At Home?
For what purposes is polycarbonate glue used and what types are there? How to glue transparent polycarbonate to each other or to metal? How does the gluing process take place? How can you glue it at home? Useful tips for buying and working with polycarbonate adhesive
Grinding Timber: How To Grind Wooden Walls? How To Grind The Ends With A Grinder And Make Them Smooth With Your Own Hands? What Is Better To Grind For Painting?
Grinding timber: what is it and how to grind wooden walls? How to properly handle glued and profiled timber? When does it become necessary to grind wood with a sander?