2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-18 12:09
The preparation of OSB boards for subsequent cladding has a number of nuances, and last but not least, it is puttying. The overall appearance of the finish and the stability of the outer layers largely depend on the quality of this work. Let us dwell in more detail on which putty compositions are used for indoor and outdoor work on OSB.
Species overview
OSB is a multi-layer board made from wood-fiber shavings pressed and glued with synthetic resin under the action of heat and increased pressure. All layers have different orientations, due to which the board acquires exceptional resistance to deformation.
This is a fairly common finishing material. However, working with it requires certain skills and knowledge. Despite the high percentage of synthetic substances, 85-90% of such panels are composed of wood-fiber components.
That is why they have many of the characteristics of natural wood, including the ability to absorb water.
This feature raises great doubts that such a panel can be putty . It is possible, puttying of OSB sheets is allowed. At the same time, the technology for performing work inside the heated room and outside is practically the same.
Puttying allows you to achieve the following results:
- protection of the wood-fiber structure of the panel from atmospheric influences - precipitation, vapors and direct UV rays;
- protection of OSB sheets from aggressive components, which are present in large quantities in facing materials;
- prevention of the appearance of tarry discharge on the finish veneer;
- masking joints, cracks and other installation flaws;
- formation of a leveled monolithic layer with high adhesion;
- getting the illusion of a concrete surface, hiding the wood texture;
- additional protection of premises from volatile formaldehyde compounds.
For finishing OSB boards, different types of putty are used.
Oil and glue
The main components of oil glue putties are:
- drying oil;
- adhesive composition;
- plasticizer;
- thickeners;
- fungicides;
- water.
It is used in warm rooms for wallpapering, as well as for subsequent painting. It is not applied under plaster. Does not mask defects larger than 0.5 cm.
Pros:
- economical consumption;
- affordable cost;
- no release of volatile toxins;
- distribution over the surface in a thin layer;
- the possibility of manual grinding;
- ease of use.
Minuses:
- can be used exclusively at temperatures over 15 degrees;
- does not withstand strong temperature changes;
- putty coatings do not withstand moisture and are quickly damaged by mechanical stress.
Polymer
This putty based on acrylic or latex can be used for finishing all rooms, including bathrooms, swimming pools, kitchens, as well as unheated country houses. It is allowed to use acrylic putty outdoors when finishing facades. It goes well with any subsequent finishing options.
Pros:
- forms an ultra-thin snow-white coating;
- has good sound insulation;
- resistant to fungi;
- moisture resistant;
- vapor permeable;
- tolerates heat and temperature fluctuations;
- durable;
- plastic;
- without smell;
- durable.
Minuses:
- latex resins can only be applied in a very thin layer;
- the putty dries quickly, therefore it requires the fastest possible application - in the absence of work skills, this can lead to the appearance of defects and the need to rework the entire work.
And, finally, the main drawback of latex putties is the high price.
Other
There are several other types of putties that can be adhered to wood - these are alkyd (nitro putty) and epoxy. The coating formed by these compounds is characterized by strength and long service life.
At the same time, they have a number of disadvantages. So, alkyd mixture is quite expensive and extremely toxic - it is more often used for repairing vehicles . Epoxy - forms a tough but vapor-proof coating with low adhesion to the finish. In addition, like nitro putty, it has a high price.
It is more often used for the restoration of small areas on the surface, but it is unsuitable for serious repair and finishing work.
Popular brands
SOPPKA . This putty is used to correct defects and fill irregularities of OSB boards, as well as fiberboard, chipboard and plywood. It is applied before finishing in wet or dry rooms. The surface of the putty is well sanded, it can be pasted over with acrylic or vinyl wallpaper, as well as painted.
Fungicidal additives are introduced into the composition of the material, which protect the fibers of the panels from all types of fungus and mold.
The advantages of the putty include:
- ease of application;
- resistance to cracking;
- high adhesion;
- environmental safety;
- lack of a sharp chemical odor.
NEOMID . It is a water-based polymer putty. Used for work in dry and damp houses. When applied, they form an elastic, moisture-resistant coating. Does not crack. Gives the surface strength and durability. After drying, it can be sanded, as well as subsequent wallpapering and painting.
Semin Sem . Another water-based putty for OSB sheets. It is used in dry and damp rooms, for cladding the surface of walls, ceilings, as well as seams. It has elasticity, moisture resistance and resistance to cracking. Differs in high adhesion, therefore, when used in interior decoration, it is not necessary to prime the surface. For exterior finishing, it can be used in conjunction with facade primer. Hand-sanded well.
Can be further dyed or wallpapered.
Nuances of choice
Regardless of what components are the basis for the production of putty, it must have a number of characteristics
- High adhesion . Any boards made of oriented strand materials are usually coated with resins or wax. Therefore, not every putty can firmly adhere to such a surface.
- Homogeneous consistency . The putty composition should not include large-sized particles - this can significantly complicate the performance of finishing and facing work.
- Low shrinkage . This property minimizes the risk of cracking as the filler dries. Thus, the quality of work increases and the time for their implementation is reduced.
- Hardness . Putty mixtures used for such a complex material as OSB boards should be as hard as possible, but at the same time it is good to be sanded, including by hand.
- Possibility of subsequent finishing . The putty is used as an intermediate stage of facing. Therefore, the dried, sanded surface of the material must be suitable for various types of further cladding, be it painting or wallpapering.
When buying a putty, it is very important to choose the right putty composition, since the quality of the repair performed and its duration largely depends on it . Most of the failures in the work are associated with the miscalculations of unskilled craftsmen who performed the putty.
So, cement and gypsum building mixtures are not suitable for working on OSB . Of course, they are cheap, differ in density, mix well and distribute without problems on the plate. But their main drawback is the lack of elasticity. The tree periodically changes its volume depending on the temperature and humidity parameters in the room, so both the starting and finishing putty will lag behind it.
Due to the popularity of OSB boards in repair and decoration, a large selection of putty compounds from different manufacturers has appeared in the construction segment . Of all the variety, you need to choose the most elastic solutions that are optimal for working with wood-based materials.
It is better to give preference to ready-made compositions in cans or plastic buckets . Their use will protect against mixing errors of the active composition. In addition, it will allow you to take your time when distributing the solution for fear that the freshly diluted mixture will dry out quickly. The only drawback of such a solution is the high cost, such a putty will cost much more than dry packaged formulations.
It should be noted that the definition of "putty" is often used in the names of mixtures . In theory, both "putty" and "putty" mean the same thing. These words came into use at different times, but today both terms are allowed to be used.
Application features
When all the working material is selected and purchased, you can proceed directly to puttying. There is not much difference in how to putty the panels under paint or under wallpaper - the sequence of actions will be the same in any case.
The first stage involves the application of a primer with high adhesion characteristics. This solution creates a film on the surface of the material, it prevents the appearance of resinous stains, essential oils and other components present in the wood
Then you need to take a short break for the final drying of the surface. Its duration directly depends on the type of primer and averages 5-10 hours
The next stage is the direct application of the putty. We draw attention to the fact that this work can be performed only at positive temperature values of the air, at a humidity level not exceeding 60%
After applying the putty, you should arrange another technological break for its final drying
At the third stage, the surface is sanded to make it smooth, even and eliminate all defects. If necessary, reinforcement with a metal mesh is performed
It's obvious that puttying OSB panels is a simple job and you can cope with it yourself . Nevertheless, theoretical knowledge alone is not enough to putty such a capricious material. Therefore, in the absence of skills in working with wooden surfaces and building mixtures, it is better to turn to professional craftsmen.
In our review, we tried to answer as fully as possible the question of which finishing materials are best used for puttying OSB panels, how to finish . In conclusion, we note that there is no need to putty at all, if you are not going to mask the structure of the wood material. But for gluing wallpaper, as well as for painting, such a finish is necessary - it will protect the base from moisture and allow you to form a durable decorative coating.
Recommended:
Boards 50x150x6000 Mm: How Many Pieces Of Boards 50 X 150 Mm In 1 Cube? Edged And Unedged Boards, Their Weight. Planed Dry Boards And Other Types
Where are boards of 50x150x6000 mm used? How many pieces of boards 50 x 150 mm in 1 cube? What is the difference between edged and unedged boards, what is their weight? What types of wood are these lumber made from? What are the characteristics of planed dry boards and other types?
OSB Painting (41 Photos): What Paint To Paint The Plates? Primer Paint For OSB Panels, Rubber And Other Types. How Beautiful Can You Paint OSB Sheets?
How is OSB painting carried out? What paint to paint the slabs? Primer paint for OSB panels, rubber and other types - what are the characteristics, which one to choose? How beautiful can you paint OSB sheets? Overview of manufacturers of cladding products. OSB panels painting technology, several recommendations
Wall Painting (67 Photos): Stylish Black And White Painting Of Apartments, Modern Art Acrylic Painting In The Interior Of The Living Room And Other Rooms, Other Types Of Painting
Wall painting is a popular trend in modern room design. What are the features of a mural? In what cases is a stylish black and white painting of apartments used? Variety of techniques used for this purpose
OSB Sheets 12 Mm: 2500x1250 And Other Board Sizes, Standard Weight Of OSB Sheets And Self-tapping Screws For Them. How Many OSB Boards Are There In A Pack? Thermal Conductivity
What is remarkable about OSB sheets 12 mm thick, what you need to know about 2500x1250 products and other plate sizes? What is the standard weight of OSB sheets, and what screws should be used for them?
Dimensions Of Decking Boards: Thickness And Width Of Outdoor Boards, Polymer Boards 4-5 And 6 Meters, WPC Boards Of Other Lengths
Decking is one of the most popular materials used in home decoration. But how to choose the dimensions of the terrace board, what should be the thickness and width of the boards for the street, and also how the polymer boards of 4-5 and 6 meters differ, we learn from this article