Brazier From A Drum Of A Washing Machine (24 Photos): How To Make A Smokehouse From A Tank With Your Own Hands, The "ram" Option From An Old Machine

2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-09 13:15

Today, it is quite inexpensive to purchase various variations of barbecues in almost any store: from disposable designs to forged products. But you don't have to waste time and money, because on the balcony, in the garage or in the country you can always find suitable parts for assembling the original barbecue for free.

What can be made of?

One of the most suitable options for remodeling would be a drum from an old washing machine. You can turn it into a brazier in just 2-3 hours on your own and without much effort. You don't need any special skills for this, just read the simple instructions.

To create a homemade barbecue, you need to think about all the subtleties of the design of this product. The most basic thing is the brazier.

It should be both capacious for a large amount of coal and compact, so that its operation does not require equipping a separate platform.

And, of course, it must be durable so that you don't have to do it all over again for the next season.

If you have an old washing machine standing idle, the drum from it perfectly meets all the requirements described above . As a rule, drums are made of high-strength stainless steel, which copes excellently with the effects of corrosion and high temperatures. A brazier, converted from a washing machine drum, can be installed in the open-air courtyard, without worrying about its safety during bad weather. In addition, its operation does not require pretreatment, since it is hygienic due to the absence of rust.

The design of the drum provides for the presence of many small holes in its walls.

They will allow air jets to circulate freely through the body of the barbecue, stimulating the smoldering of coals and shortening the time for cooking vegetables or meat.

This allows significant savings in kindling material.

The drum itself, in addition to its strength, is very light , which will allow you to take the brazier made from it with you to nature or put it in the closet until the next time - it will not take up much space. And you can use it for many years.

Purchased brazier designs are usually made very handicraft, the parts for assembling the brazier and stands are sloppy, and often dangerous with their sharp edges. Before use, they must be filed to make them safer. The drum has no sharp corners, therefore, a homemade grill will be 100% safe, and if you show your imagination a little, then it will be beautiful.

What do you need to build?

The most amazing thing is that no special elements are required for the production of a barbecue. If the height of the future barbecue is not important, except for the drum itself, nothing else can be used. If you need to make it on a stand, then you will also need a metal pipe. The length and diameter must be selected depending on the size of the drum and the required height of the manufactured product.

It is not necessary to use a pipe to make a barbecue stand . You can look around and be smart: old metal shelves, flower stands or a frame from an old chair are fine. The main thing is to understand: is it possible to fit the found product under the barbecue stand.

Of other consumables, you need to prepare a dozen bolts and two corners 40 cm long. The length is approximate, you can use any available trims, adjusting them during the assembly process.

The tools should be prepared in advance: a drill, pliers, a grinder, a tape measure, a file, a marker and a metal saw. The latter can be excluded if you have good experience with the grinder. The main thing is to observe safety precautions, and not to cut off excess from the drum of the washing machine.

Manufacturing instruction

After the completion of all the preparatory work, the process of assembling the barbecue itself begins. First, using a grinder, a rectangular hole is cut in the flat wall of the drum body. This will be the hatch of the future barbecue. With a hacksaw, you can trim the edges to make them smoother. If the drum is initially too large, it can be pre-divided into two parts with a grinder. Then one part must be inserted into the other and the joint welded to avoid the risk of heat loss.

Then, at the corners of the resulting rectangle, holes are drilled for bolts with a diameter of about 10 mm. Using the resulting holes, metal corners are attached to the edges of the hatch and secured with bolts. This will allow you to distribute the skewers evenly when frying the kebabs.

This completes the process of making the brazier in principle . Further manipulations for decorating it can be done at your discretion. The most common option is to attach three short tubes (about 10 cm long) to the top of the case, on which the grill is installed. So, the grill will also serve as a barbecue.

After that, you need to prepare the stand. If a ready-made product is used for this (flower stand, rack, ready-made legs), then it is enough just to check its stability and install the brazier on top. If a pipe is used, then it must first be fixed to the ground, and then the drum body must be screwed on. You can use a thin metal tube by dividing it into three parts, making a tripod. In this case, it is not necessary to weld them together, you can fasten them tightly with bolts and a corner, make them removable.

It is also recommended to attach one cross tube to make the resulting tripod more stable.

Mounting the barbecue body will be similar to using a ready-made stand.

Some models of drums have factory holes for attaching it to the body of the washing machine . They can be bored to the diameter of the pipes used, and threads can be cut on the pipes themselves. After that, it remains just to screw the pipes into the holes, having received a folding version of the legs for the barbecue. It is worth paying special attention to fitting the pipes to the holes so that they do not dangle when twisting, otherwise the grill will not be stable. This can be done even if there is no experience in such work at all.

If there is a possibility and practice of using a welding machine, then a rotating stand can be made.

For this, profile pipes and corners are used, from which a tripod is assembled, which is attached to the axis of the drum. After assembly, the brazier will rotate, independently inflating the coals as it rotates through the side holes.

Another option for making a barbecue: make a rectangular hole in the side rounded wall of the drum. Then the grill will function as a grill, but its operation will require a certain skill. Moreover, such a grill definitely needs doors to maintain the internal temperature of the chamber. And also the drum body can be cut across, fastened with bolts - you get a full-fledged portable grill for camping lovers.

The finished grill does not need to be painted, as it is initially protected from environmental influences.

You can paint the stand if it is not made of stainless steel. As a decor, you can think of options for various useful devices: make a canopy for the barbecue so that it can be used in rainy weather, attach holders for inventory (forks, skewers, tongs), upgrade the rack for the grill or skewers on top of the case.

In addition to its direct purpose, the brazier can be used as a fireplace in nature or a summer residence in the cool season.

Such a hearth does not require constant throwing of firewood, but functions due to constant air circulation inside. If you also give it an aesthetic appearance, then it will give a certain romanticism to outdoor recreation.

A home-made brazier from the drum of an old washing machine will serve a long service with minimal costs for its manufacture and will help to fry a ram in the shortest possible time.

The original look will appeal to close and familiar people , and the realization that it is made by hand will give the kebabs cooked on it a special taste. A smokehouse from a machine tank is an original idea that will appeal to many.