Rack Jacks 3 T: Characteristics, How It Works And Where It Is Used

2024 Author: Beatrice Philips | [email protected]. Last modified: 2023-12-16 05:33

Rack jacks are very popular with builders and car enthusiasts . Sometimes there is simply nothing to replace this device with, and it is not possible to do without it. In today's article we will look at where this type of jack is used and how to use it.

Peculiarities

The design of the rack and pinion jack is very simple. It includes:

• guide rail, along the entire length of which there are holes for fixing;
• a handle for attaching the mechanism and a movable carriage that moves along the rail.

Pick-up height can be from 10 cm , which means that you can start lifting from a very low position.

The principle of operation of this device is based on the joint operation of the rack and the ratchet mechanism . To lift the load, the lever is forced downward, at this time the carriage moves exactly 1 hole along the rail. To continue lifting, you need to raise the handle again to its original position at the top and lower it again. The carriage will jump 1 hole again. Such a device is not afraid of contamination, therefore it does not need lubrication.

If, nevertheless, dirt has formed on the mechanism, then they can be cleaned with a screwdriver or gently knock on the carriage with a hammer.

The described tool has several advantages

• The design is easy to use. The device is unpretentious and capable of working in extreme conditions.
• The design is capable of lifting loads to a great height, which other types of jacks are not capable of.
• The mechanism works very quickly, lifting takes a few minutes.

Rack jacks have many disadvantages that you need to be aware of

• The design is very cumbersome and extremely inconvenient to transport.
• The area to support the jack on the ground is very small, so an additional stand is required to increase the area of contact with the ground.
• As for cars, such a jack is not suitable for all types of cars due to the specifics of the lifting.
• Injury hazard.

You need to work with such a jack very carefully, observing all safety rules … In addition, in the raised state, the structure is very unstable and under no circumstances should one climb under the machine raised by such a jack - during lifting there is a risk of the load falling off the device leg. In this case, the operator must take the safest position and, in case of danger, leave the area where the jack falls very quickly.

In addition, if the load nevertheless fell off and the jack was clamped, then its handle can begin to move with great speed and force. Thus, excess weight is removed from the carriage. In this case, you need to give the mechanism the opportunity to free itself. Do not try to catch the lever, you will not be able to do this with your hands, because at this moment the load presses on it.

Many try to catch the lever, such attempts end with knocked out teeth and broken limbs.

Criterias of choice

Choosing for yourself a rack jack for 3 tons, you need decide on its length , because the maximum weight is already known. There is a misconception that the color of a product affects its quality. Some argue that the best rack jacks are red, others say black. The color does not affect the quality of the product in any way.

The next important criterion when choosing is quality of parts . Most often, the rack and toe heel are made of cast iron, while the rest of the parts are made of steel. They must have a high-quality coating, without visible defects. It is best to purchase such tools in branded stores with a long-term positive reputation ., where the likelihood of running into a low-quality product is extremely small, and experienced sellers will help you make the right choice and help out with useful advice.

Ask the staff quality certificate for the purchased products, this will protect you from buying a fake.

If for some reason they cannot provide you with this document, then it is best to refuse to purchase in this institution.

How to use?

The rack jack for 3 tons is very easy to use . The carriage has a lift direction switch. If the product without load is switched to the lowering mode, then the carriage will move freely along the rail. In the case of installation in lifting mode, the mechanism begins to work according to the principle of a reverse key, moving only in one direction (up). In this case, a characteristic crackling sound will be heard. This is necessary for quickly setting the device to the desired height.

Lifting is carried out using a lever - it is necessary to press on it with force, and in the lower position, fixation takes place on the next tooth.

It is very important to hold on to the lever firmly, as if it slips, it will begin to return to its original position with great force . Lowering a load requires more attention than lifting. Since everything here happens in the reverse order and you do not need to press on the lever, and not let it shoot into the rail. Many people forget about it and get severely injured.

And the most important - make sure that your fingers, head and hands are not in the flight path of the sliding lever.

Take the safest position so as not to lose your health in case of unforeseen circumstances.