2024 Author: Beatrice Philips | [email protected]. Last modified: 2023-12-16 05:33
Often in the process of construction or repair, it becomes necessary to glue two materials that cannot adhere to each other. Until recently, this was an almost insoluble problem for builders and decorators. However, these days, such tasks can be solved using a special primer called concrete contact.
Characteristics
Concrete contact consists of:
- sand;
- cement;
- acrylate dispersion;
- special fillers and additives.
The main characteristics of the concrete contact:
- used for non-absorbent surfaces as an adhesive bridge;
- designed to strengthen the surface;
- consists of safe substances;
- does not have an unpleasant, pungent or chemical odor;
- forms a waterproof film;
- prevents the development of mold and mildew;
- for control during application, a dye is added to the concrete contact;
- sold as a solution or ready-to-use;
- dries from 1 to 4 hours;
- the diluted composition of the concrete contact does not lose its properties within a year.
Suitable for the following surfaces:
- brick;
- concrete;
- drywall;
- tile;
- gypsum;
- wooden walls;
- metal surfaces
Some experts note that the composition does not fit well on bituminous mastic, so it is better not to use a solution with it.
What is it used for?
Concrete contact is a type of sand-cement-based primer with a large amount of polymer additives. The main task of this material is to increase adhesion (adhesion of surfaces to each other). In a few minutes, you can increase the adhesion of any material to the wall. To do this, you only need to apply concrete contact.
It is very difficult to apply plaster on a completely flat wall - it will flake off and then fall to the floor. After processing with concrete contact, the wall becomes slightly rough. Any finish will easily fit on such a basis.
How to prepare the mixture?
Often there is no need to prepare this mixture - manufacturers are ready to sell a completely ready-made solution. When buying such a concrete contact, it is enough to stir the entire contents until smooth. It must be remembered that it can only be stored at freezing temperatures.
Nowadays, few people prepare such mixtures with their own hands, because you need to know exactly the proportions, buy all the necessary materials, and also properly dilute them with water. Then you need to wait and watch how the solution thickens. This is extremely energy-intensive, so everyone buys a ready-made concrete contact. You just need to read the instructions for use and work correctly with this composition.
Application process
Before applying, you need to know:
- concrete contact can only be applied at positive temperatures;
- relative humidity should not exceed 75%;
- you can apply anything to the solution only after 12 - 15 hours;
- it is necessary to properly prepare the surface.
In the presence of dust, the quality of the concrete contact will noticeably decrease . Painted walls should take a long time to finish. You can also use detergents.
It is impossible to reduce the consumption of the solution - this can lead to the formation of places with low adhesion on the wall.
After preparing the surface, you can start the main work:
- it is necessary to remove the old coating. It is best to use brushes for this job;
- the solution must be prepared only according to the instructions;
- this mixture cannot be diluted with water, otherwise the entire product will become unusable;
- the solution must be applied with an ordinary roller or brush;
- when the material dries, it is necessary to apply a second layer;
- after applying the second layer, it is necessary to wait a day to continue finishing work.
With the help of concrete contact, walls can be prepared for further finishing. The main thing is to use the solution correctly and not dilute it to increase the volume.
Recommended:
Whitewashing The Walls: How To Whitewash The Walls And Ceiling During Repairs And How To Properly Dilute The Whitewashing Composition, How To Extinguish And How To Dilute Lime
How is the wall whitewashed? How to whitewash the walls and ceiling during repairs and how to properly dilute the whitewash composition? What products will help extend the life of a whitewashed wall? What is the most sustainable and sustainable wall whitewash product?
How To Dilute The Putty? How To Dilute A Mixture For Walls At Home - The Right Proportions, How To Make A Solution Without Lumps
How to dilute the putty? This question is often asked by people who decide to make repairs on their own. Puttying is one of the important preparatory stages, on which the quality of the final result depends. Not everyone can afford ready-made compositions, therefore, a huge selection of dry powders is offered on the construction markets, which, if the correct dilution proportions are observed, can become a worthy alternative to expensive ones. It is about how to properly dilute putty at home
DIY Venetian Plaster (63 Photos): Application Technology, How To Apply Correctly, How To Apply On Walls And Ceiling
What is it - this famous and almost unknown Venetian plaster? Can you use it to update the old walls of your favorite room with your own hands? What is the technology of its application and what types of Venetian plaster are there in the world? If you decide - how to correctly apply the Venetian on the wall so as not to ruin everything? These and other questions will be answered by my new article "Do-it-yourself Venetian plastering"
How To Prime The Walls Before Wallpapering? How To Apply A Primer Before Puttingty, How To Properly Apply To Drywall
The primer is an excellent tool for wallpapering walls. How to prime the walls before wallpapering? How to apply a primer before puttingty, what type of material to choose for a specific surface? What is so special about a primer that makes it popular?
Arbolite Or Expanded Clay Concrete: Which Is Better? Thermal Conductivity Of Wood Concrete In Comparison With Foam Concrete, Sawdust Concrete, Aerated Concrete, Polystyrene Concrete And Straw Blocks
Before building any structure, it is important to decide which of the building materials is suitable for this. For example, wood concrete or expanded clay concrete. These are two lightweight concrete types with their own advantages and disadvantages. But which one is better? And how much the thermal conductivity coefficient of wood concrete differs in comparison with foam concrete, gas silicate and sawdust concrete