Partitions From A Bar: Installation Of Interior Decorative Partitions And Their Manufacture, Partitions 50x50 And Other Sizes For Zoning Space In An Apartment

2024 Author: Beatrice Philips | [email protected]. Last modified: 2023-12-16 05:33

Often in the process of repair work there is a need to create partitions. Such designs allow you to form indoor zoning. They can be made from a wide variety of materials. Today we will talk about what are the main features of bar partitions, and how you can make them yourself.

Advantages and disadvantages

Partitions from a bar have a number of important advantages, among which the following stand out

1. Allows you to zone the space. Interior partitions made of wood are load-bearing structures, they are intended only for dividing into separate rooms.
2. Environmental friendliness of the material. The timber will not emit during operation harmful substances harmful to humans and their health. Such material is considered absolutely safe.
3. Easy installation technology. To create partitions from such material, you do not need to turn to the help of professionals, anyone can make them on their own.
4. Nice appearance. Often, timber surfaces are used as an interesting accent in the interior of a room. In addition, if desired, such partitions can be beautifully decorated.
5. Low cost. Such material can be attributed to the budget group.

Despite all the advantages, such partitions also have some disadvantages, which should also be taken into account

1. The need for particularly careful processing. The timber that will be used in the manufacture should be well prepared. Provide in advance noise insulation, protection from moisture, temperature extremes.
2. Dependence on the level of humidity. Sometimes, even when providing protection from water, the wood begins to absorb liquid, which leads to the expansion of the material, later the wood will begin to deform, and the wall plane will bend.

Requirements

Such structures are self-supporting structures, since they are not subject to heavy loads from the roofing and floors located between floors. The following requirements are imposed on partitions from a bar:

• small total weight;
• minimum possible thickness;
• a sufficient level of strength to support suspended structures;
• ensuring good sound insulation of one room from another;
• assembly from parts that are normally combined with load-bearing enclosing elements.

Type overview

Bar partitions most often play the role of room structures in an apartment or house for zoning a common space … Similar structures can be made solid option . You can also make a partition with a door. They are more often used for large spaces. As a rule, for this, models are purchased with dimensions of 150x150, 40x40, 50x50, 50 by 100 millimeters.

Sometimes such partitions act as frame for the room . Frame options are considered the cheapest option. They will be affordable for any person. Exist frame-panel models … They are formed in several layers.

Such partitions are heavy. They should not be used as structures for a frame room. Sometimes such structures are made from OSB sheets.

Another type is squared solid partition . It is a structure consisting of several large boards that are mounted in a vertical position using a tongue and groove. Fixation takes place with a special strapping.

Tools and materials for installation

If you want to assemble and install the partition yourself, then you first need to prepare all the necessary devices and materials for this:

• timber;
• saw;
• hacksaw for wood;
• drill with a special drill for wood;
• chisel;
• axe;
• a hammer;
• building level;
• roulette.

Manufacturing technology

The manufacturing technology of such structures from a bar will depend on the specific type of construction . Let's take a look at how to make and install a simple wireframe model. First you need to form a base from a bar measuring 50x50 mm. Vertical lines are created along the load-bearing wall covering, from which the structure will go, they must be placed parallel on the ceiling and on each side. The construction made will be the basis for the future partition.

Then you need to fasten the beam, start from the side sections in an upright position from the floor. Connections are made using wood screws. After that, mark about 10-15 centimeters from the ceiling and form a spacer across the entire width of the coating. The structure is attached to the top with elongated screws.

In the lower part, another bar is connected in parallel to the floor covering. Its ends are fixed with lateral parts. All connections are recommended to be made with metal corners . After that, with a pencil, it is worth noting the exact location of the opening. When all the marks are made, in the direction from the upper to the lower beam, two beams are passed at the distance of the intended opening.

Next, the frame is passed additional bars (the step should be 60-70 centimeters). This should be done in an upright position. Between these elements, spacers are created from a shortened bar. It is better to make another spacer in the place above the opening.

It is better to cover the frame with sheets of gypsum fiber board or gypsum board

In the process of registration, care should be taken to create an insulating layer. A special vapor barrier must be laid between the wood material and the insulation. This is necessary in order to protect the inside from the negative effects of moisture.

Some partitions are fixed with a tenon and a groove . In this case, it is necessary to draw a straight line in the main wall, then on each side of it mark half the width of the thorn.

The spike should be carefully shaped from the ends in the bar . This can be done with a simple saw or a hacksaw. The height of the spike should be approximately 35-50 millimeters. A groove is formed in the wall along the two extreme lines made to the corresponding depth. Flax fiber or tow must be placed in the groove.

The first bar is installed on the floor, which is pre-laid with jute tape. The material is screwed to the flooring with wood screws. Next, make holes for the pins with a drill. After that, the second bar is laid with spikes in the groove. In this way, make up to the end of the partition.

If a doorway was provided in the frame part, then rigid elements must be installed … They are attached to the upper bars of the structure with metal corners. This type of partition will be the best option when creating a structure from a profile bar.

When constructing such partitions, installation in a groove without a thorn is possible. In this case, a straight line is drawn in an upright position to the wall to which the structure will be attached.

Half of the width of the timber recedes from it, after which two more parallel straight lines are drawn.

A groove is formed along the extreme straight lines, its depth should be 30-50 millimeters. Next, jute is placed in the groove made and the ends of the timber are inserted there. Installation is carried out using jute dowels. When the structure is completely assembled, the jute is blown through. If you pre-insulated with a special tape consisting of flax fiber, then you can skip this procedure.

Remember that there are two main installation methods in total . For any buildings made of different materials, it is possible to install a ready-made frame structure. In this case, you just need to fix the structure on the walls, floor and ceiling. This can be done with dowel-nails.

The second installation option can only be used for ready-made log cabins … In this case, it is better to erect the partition right on the spot. To do this, you need to make an accurate markup. Further, along the lines made, the bars are fixed, which will make up the frame, and then the rest of the whole is assembled. At the end, you can add decorative elements.

When erecting such partitions don't forget about insulation, insulation and protection . For this, mineral wool or polystyrene is laid in the formed voids. Other insulating material can be used. Sometimes such partitions are also created in bath rooms with sudden temperature changes. In this case, the structure should not contain any additional metal elements.