2024 Author: Beatrice Philips | [email protected]. Last modified: 2023-12-16 05:33
Concrete structures and floors have a long service life, however, with long-term loads, temperature and humidity changes, cracks, chips or other damage may appear on the surface.
These defects can be eliminated using various repair mixtures. However, if a poor-quality product is selected or if it is used incorrectly, defects may appear after a couple of years, and they will need to be repaired again.
Damaged concrete structures require urgent repair . Otherwise, the crack will quickly spread under the influence of constant loads. Nowadays, this problem can be easily solved with Emaco dry mixes.
Specifications
Emaco repair mortars are used to fill cracks no more than one centimeter wide. This mixture has high adhesion to concrete, brick and reinforcing mesh. The finished composition is capable of withstanding mechanical loads, is distinguished by its durability and reliability. It is noted that the mixture is easy to fit and has sufficient elasticity. This allows you to get the job done quickly.
Considering dry mixes for working with concrete or brick surfaces, you need to know the basic conditions for their correct use:
- Their moisture content should not exceed 1 ppm;
- Shrinkage of solutions is unacceptable;
- The entrained air is allowed no more than 5%;
- Frost resistance must be at least F300;
- Products are packed in open and closed paper bags;
- The repair mixture is fireproof, explosion-proof and non-radioactive;
- The use of the ready-made mixture should be carried out only in rooms with an exhaust hood or with good ventilation;
- Work must be carried out exclusively with personal protective equipment;
- The dust in the package should be no more than 3-5 mg per cubic meter. m.
Application
The use of various types of mixtures is possible only if certain rules are observed:
- They should be stored and used only at temperatures from +5 to +30 degrees;
- Mixing the mixture should be done using mixers or a drill with a special attachment; manually - not allowed;
- The mixing time is 5 to 7 minutes;
- The volume of the finished mixture should be such that it can be consumed in half an hour;
- The amount of water in the mixture should not exceed the value indicated on the package;
- Before repair work, the surface must be prepared by removing dust, dirt, oil stains and damaged concrete; after that, it needs to be slightly moistened;
- The composition hardens for a day in conditions of minimal moisture evaporation.
Mix brands
There are many different Emaco formulations. Each of them is designed for specific types of work.
Emaco S88 and S88C
This group of polymer-cement mixtures is used for repairing small areas up to 3 mm deep. When mixed with water, it forms a compound with high adhesion to concrete, brick and steel. Over time, the mixture does not stratify.
It is successfully used in the repair of premises with high humidity, but is not suitable for working with wood. Be sure to wear gloves.
EMACO 90
The composition includes cement, sand and various polymers. It is used to repair large cracks, up to half a centimeter wide. Suitable not only for renovation, but also for the restoration and strengthening of concrete. It is resistant to all weather conditions. The composition should be stored only in whole packages in rooms with low humidity.
MasterEmaco S 466 and Emaco S66
These compounds are used for filling large cracks up to 10 cm deep. They form a cast material that does not delaminate over time.
It can be used for the restoration of concrete floors not only in residential but also in industrial premises. Moreover, work can be carried out with concrete floors, and with supports from the same material.
The use of Emaco products allows you to extend the life of all possible concrete structures . The most important thing is not to delay and complete this work on time, choosing the composition necessary for these purposes.
Recommended:
Roofing Material (41 Photos): What Is It? Types Of Roofing Material In Rolls And Brands. Deposited Material With Chips And Other Types, Material Characteristics
Roofing material - what is it? What are the types of roofing material in rolls and its brands? What you need to know about the deposited material with chips and other types, how to choose, use, store and dispose of it?
Stekloizol (45 Photos): HPP And TPP, HKP And TKP, Application And Technical Characteristics. Is It Better Than Linocrome And Roofing Material? Reviews
Stekloizol HPP and TPP, HKP and TKP - is it better than linocrome and roofing material? Application and technical characteristics of the material, features of its laying and marking. Customer Reviews
Oil Paints: How Long Does The Composition "PF-115" Dry For External And Internal Works, Technical Characteristics And Consumption Per 1m2
Oil paints are a fairly reliable coating, although not perfect. How long does a composition intended for different surfaces dry? What is good about PF-115 paint and how to choose the optimal solution for external and internal work in a particular case?
Mortar Mixer: Mobile Stirrers For Mortar, Models For 65 L And Other Volume Of Mortar, Forced Action Mortar Mixer And Other Stirring
What is a mortar mixer, what design features does this equipment have and what is it intended for? What are the criteria for choosing the right mobile mixers for solutions, as well as models for 65 liters and with a different working volume?
Roofing Material Of The RKK 350 Brand: Technical Characteristics In Accordance With GOST, The Thickness Of The Roofing Material. How To Stack? Weight And Service Life, Dimensions
Roofing material RKK 350 - technical characteristics according to GOST, composition and thickness of roofing material, main areas of application, weight and service life, dimensions. How to lay roofing material on the roofing base?