Hose Reel: How To Make A DIY Wall Mounted Garden Hose Reel? Gardena Trolley, Reel And Other Models

2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-09 13:15

The reel is a functional device that makes it much easier to work with the hose. Users cannot fail to appreciate the convenience and advantage of this device when cleaning dirty hoses from the floor in a production workshop or from garden beds in the country.

Varieties

The diameter of the coils can vary considerably, they can fit hoses of the following length (m):

• 25;
• 40;
• 50;
• 90.

Coils can also be mobile and stationary with inertial automatic units, on carts with rollers. During operation, there are many reasons to wind the hose onto the reel without leaving the workplace. This ensures the safety and ease of use of the equipment, such devices effectively extend the service life of the equipment. Hoses are used in a wide variety of applications:

• wash transport;
• watering the backyard;
• cleaning equipment in production.

The environment actively acts on the material of the hose, it is often aggressive, contributing to its rapid wear. The stainless steel hose reel is a device that effectively extends the service life. This is especially true for chemical, furniture, mechanical engineering and food production. In private households, a hose reel on wheels is also often extremely necessary during the warmer months. Typical hose reels used in everyday life have the following length (m):

• 8;
• 10;
• 14.

If a longer hose is required, this automatically leads to an increase in the cost of the reel-reel. The most common hose diameter is 19 mm. More often than not, this "caliber" is quite enough to solve even complex problems. The coil itself will inevitably slightly reduce the dynamics of the fluid flowing through the hose.

It should also be borne in mind that the speed of water flow decreases the branch pipe (fasteners that connect the pump to the hose).

To illustrate this, a pump generates 92 liters of water per minute. Placing the hose on a one-inch reel will result in a 15% loss in fluid flow. There are many types of different coils, the most popular of which is a self-winding bobbin, such devices usually function from an electric drive. The automatic coil, which is powered from a 220 volt network, is equipment that is easy to work with, its disadvantage:

• is quite expensive;
• during installation, careful adjustment is required;
• needs a stable mains supply.

The electrically driven drums are also powered by a diesel generator. Control is carried out using a remote control. Also very popular are outdoor stationary drums, which are equipped with special stands-legs, which securely fix the device, not allowing it to be moved around the workshop.

Wall-mounted devices are also in demand, which can be fastened with a reliable clamp at any point in the vertical plane. Spring coils are also widely used all over the world, they have a return mechanism, while there is a special fixing spring that makes it possible to return the bobbin to its original position.

Benefits from purchasing a drum:

• the friction of the hose on the floor is reduced to zero, which increases the service life;
• the risk of falling and getting injured is reduced;
• the workplace becomes more functional;
• labor productivity increases.

When using the coil, the following points should be taken into account

• The reel can quickly deteriorate if it "deals" with a substandard hose.
• If the hose is too long, it is more likely to rupture. The speed of movement of water in the hose is rather big, the greater it is, the more chances that a rupture may occur in some place.
• It is always recommended to leave a long hose on the reel, it should be evenly positioned on it.
• Before purchasing the device, it is recommended to consult with a specialist who has practical experience.
• You should buy a drum on trading floors that have a good reputation.
• You should buy goods from manufacturers that provide warranty periods.

Manufacturers and models

There are several brands that have proven themselves at their best. Product prices are quite high, but the coils have a long service life, they are reliable and work flawlessly. These include the Gardena and Hozelock trademarks.

Gardena reels have automatic winding, the hose does not twist, does not "break". The coil support is reliable, the construction is stable. The system has compact parameters, has an ergonomic hose handle. The product can be taken, for example, on a camping trip, used in summer cottage works, used in the production workshop of a small enterprise.

An adapter is always present in the Gardena reel kits.

Drum Hozelock designed for hoses that can withstand increased pressure. The reel is made of modern innovative materials that can work in aggressive environments. Models can have both inertial winding and automatic. The drums can be moved on platform carts, there are also stationary structures. Before buying, it is recommended that you carefully familiarize yourself with the performance characteristics, see how the device works in various environments. For example, in the chemical food industry, the following material is used:

• durable PVC;
• stainless steel.

Hozelock drums are price-performance-wise, and they are quite acceptable.

The Ramex AV models (from 1000 to 5000) have proven themselves very well, for more than one year they have been the sales leaders, are inexpensive and made at a high level.

Selection Tips

When buying a reel, you should focus on which hose will be used in the work. It is more rational to use professional hoses for irrigation, they have a good margin of safety (service life up to 12 years). Such products have the following advantages:

• they are flexible, easy to fold;
• go around various obstacles at sharp angles;
• do not "freeze" from ice water.

When choosing a reel for winding, you should pay attention to the following parameters of the hose:

• section;
• length;
• what material the thing is made of.

As an agricultural tool, the hose and reel must be of the same brand, this compatibility ensures that no leaks occur. When choosing, it is recommended to use the following criteria:

• Type of fixing the hose to the wall.
• What wheels are present on the mobile model.
• What is the mount for the stationary versions. They must be strong and withstand heavy loads.
• If the sleeves are long, then it makes sense to use a base that has larger diameters and widths.
• What material is the product made of.
• What primer and enamel the device is painted with.
• What metal is the coil made of. Models made of stainless steel last longer, they can withstand heavy loads and are not subject to corrosion.

The support frame of the "trolley" must be wide and made of strong metal, in this case it will be stable, will not turn over from various loads when the hose is pulled. The wheels of the "trolley" should be wide, this will provide a comfortable and smooth movement.

Smooth winding of the hose can be done using the handle, which should be comfortable.

How to do it yourself?

For gardeners, an irrigation hose is vital, and a reel is also needed to reel it. It is not necessary to buy it in a store, you can make such a node yourself, it will cost a little. To make a homemade hose reel, you need to consider what material is best to use. For the core, a piece of pipe, a steel strip, a 22x5 mm mount may be suitable. With the sidewalls, things are a little more complicated. The material must be durable, which would not be afraid of moisture and temperature extremes.

Some craftsmen mount lids from large basins or pans, this does not seem like a bad idea, the metal is quite strong there . Before starting the installation, drawings should be made (they can be found on the Internet), it is recommended to put down the exact dimensions of the future device in them. In old metal containers, the bottom is cut off, an indent is made from the edge a couple of centimeters. This option also seems quite acceptable.

Most often, the following are used for these purposes:

• old basins;
• containers from washing machines;
• large pans.

In total, a metal circle with a diameter of 35 cm is required for the sidewall of the coil. A frame is created from a metal strip, and scraps of a thin-walled pipe are welded in the center. Sometimes, for greater rigidity, fragments from PVC pipes are inserted. A circle with a diameter of 142 mm is drawn in the center, 4 holes are drilled. To exclude kinks of the hose when attaching to the axis, a fitting is used, a watering hose is attached to it. It is even better to mount a tee, in this case there is "freedom of maneuver", you can bend the hose at any sharp angle. Excess holes can be filled with foam or silicone.

At the exit, you can attach a handle to do quick winding.

Studs are best cut from reinforcement “8”. To attach the frame, you can use the same pins; fragments of PVC pipe are put on them as handles. The connector is pulled over the hose, connected to the axle and wound. During winding, be careful not to kink the hose. If everything is done correctly, then the product will not be inferior in strength to the branded copy. You can also put wheels from the washing machine so that you can move the unit around the workshop room. A hose with a diameter of 4 cm is quite suitable for such a reel. What are the benefits:

• the drum clears the working space;
• increased mobility if the drum is attached to the wheels;
• the time for unwinding and installation is reduced;
• no creases occur;
• convenient to store in any utility room.

The second option is a budget one, plywood is used, which can be coated with a special primer, then painted with oil paint . Such processing will extend the life of plywood by 3-4 times. The side walls of the future drum are cut in the form of circles from plywood (10 mm), diameter 435 mm. Holes (14 mm) are drilled in the center, they will be used to install a drum in them.

The axle can be made by taking a metal rod or pin with a diameter of 10 mm. A certain length margin should be taken into account, it should be greater than the distance between the sidewalls. It is important to correctly distribute the cross braces. They are made from strips (size 26x11 mm, only 8 pieces). The slats are located evenly around the entire circumference.

Self-tapping screws are used to fix the rails using corners (two pieces per one rail). The pusher lock is made using a special pad. This is a board (20 mm), in which a 12 mm hole is drilled, then the rectangular section is sawn in half. The resulting halves are attached to the outer sides of the sidewalls. The pusher is made of a steel plate (thickness 2 mm), size 12x110 mm.

The pusher is fixed with a screw that goes through the axle, positioned in such a way that the axle protrudes 45 mm outward. The easiest way is to attach a stand, for this you will need board cuts (14 mm wide), the gap between the supports is 45 mm. They are fixed with transverse wooden dies. The stand is fixed on a vertical plane using clamps, brackets, corners, etc.

At the base of the supports, a "landing" groove should be created so that the knot does not jump off, a special lock is made, which is cut from a steel strip (thickness 2 mm, width 20 mm). After manufacture, the drum should be field tested. Before starting work, it is recommended to carefully check all joints and knots, there should not be any backlash or poor fasteners. If everything is fine, then you can connect the hose. The drum can also be made of PVC pipes, for this only the farm needs a special welding unit for PVC products. Typically 30 mm pipes are used. The advantage of such a product:

• not subject to corrosion;
• has good strength;
• lightweight, easy to transport.

To create a normal coil you need only 3.5 meters of pipe. You will also need 1, 2 meters of PVC pipe with fiberglass additives (to form the axis).

Storage advice

In order to properly store the hose and reels in the country, it is recommended to follow several rules. It is not recommended to connect the hose to the reel inlet pipe, although the reel has a hose. In hot seasons, you should not keep the hose and reel in direct UV light, this will prolong their service life. This recommendation is especially relevant for hoses that are made of PVC and silicone.

While winding the hose on the drum, disconnect it from the water supply system, let the water drain. A coil should be placed between the clamps, methodically rotated, while cleaning the hose from dirt with a cotton rag. The reel and hose can last for decades if stored properly. Rubber hoses have a service life of up to two decades, PVC hoses are cheaper and withstand a service life of up to 10 years. In the cold season, hoses are stored rolled up on the walls, away from rodents.

During spring and summer, hoses and reels are stored under a shed . The hose can also be left on the ground. Make sure that the hoses are not kinked or kinked. In company stores you can find forged "holders" or clamps, which are conveniently mounted on vertical planes. Often they are made in a decorative style, which can also carry aesthetic functions and safely allow you to store reels and hoses. It is convenient to use an old tire for storing reels and hoses, it is able to protect from dirt and dust.