Dielectric Glove Test: Frequency And Timing Of Inspection. How Can I Check Them? What Voltage Is Tested?

2024 Author: Beatrice Philips | [email protected]. Last modified: 2023-12-16 05:33

Any electrical installation is dangerous to humans. In production, employees are required to use special protective equipment, including gloves. It is they that allow you to protect against electric shock. In order for the protection tool to perform the tasks assigned to it, it will be necessary to carry out an integrity check in a timely manner and, if necessary, replace it with a new one.

Test procedure

If the manager takes a responsible approach to the issue of ensuring the proper level of security at the enterprise, then he will not save on protective equipment for his staff. Dielectric gloves should be integrity tested and current tested prior to use . It is they who determine the suitability of the product and the possibility of further use.

Dielectric gloves are used on installations up to 1000 V.

They can be made from natural rubber or rubber sheet . It is imperative that the length is at least 35 cm. Gloves used in electrical installations can be either seamed or seamless.

Also, the legislation does not restrict the use of two-fingered products on a par with five-fingered ones. According to the standard, it is allowed to use only those products on which there are markings:

• Ev;
• En.

There are also special requirements for the size of the product . So, gloves should contain a hand, on which a knitted product is previously put on, which protects fingers from the cold. The width of the edges should allow the rubber to be pulled over the sleeves of the existing outerwear.

For safety reasons, it is strictly forbidden to roll up gloves.

This should not be done even during the defect test. It is desirable that the water in the container where the product is immersed should be about + 20 C . Cracks, tears and other visible mechanical damage are unacceptable. If they are, then you need to purchase new gloves. Electrical installation is equipment that does not tolerate neglect. Any non-observance of safety requirements will lead to an accident.

The legislative acts clearly state the time when dielectric gloves are tested . This check is required no later than 6 months after putting the protective equipment into operation. Few things are required to test a product, so such testing is available to every enterprise.

It is important that the process is carried out by a qualified specialist with the proper level of qualifications and, necessarily, a certificate.

Necessary things

Only dielectric gloves that have no visible damage can be tested. For this, a laboratory is specially equipped. A better result can only be achieved when testing in water. In this way, even minor damage can be easily identified.

To carry out the check, you will need to prepare a bath filled with liquid and an electrical installation

Voltage

To ensure the cleanliness of the test, it will be necessary to provide the electrical installation with the required voltage. It is usually at 6 kV. On the milliammeter used, the value should not rise above the 6 mA mark . Each pair is tested with current for no more than 1 minute. First, the position of the lever of the electrical installation should be in position A. This is how you can check if there are breakdowns in the gloves. For this, signal indicator lamps are used. If everything is normal, the lever can be moved to position B. This is how the amount of current flowing through the glove is measured.

In the event that the lamp begins to signal an existing breakdown, the tests should be completed. The glove is considered defective and cannot be used.

If everything went well, the protective equipment should first be dried before commissioning , then a special stamp is applied, which indicates the tests carried out. Now the product can be sent for storage or given out to employees.

Process

Not everyone understands why dielectric gloves need to be tested, as they have probably been tested at the factory. Moreover, after six months, you can simply purchase a new kit . In fact, there are instructions for the use and testing of protective equipment. This document is called SO 153-34.03.603-2003. According to clause 1.4.4, electrical protection equipment received from the manufacturer's factory must be tested directly at the enterprise where they will be used.

It is very important to understand that if at the time of the check it turns out that a current above 6 mA passes through the product, then it is not suitable for use and should only be written off as a marriage

1. Gloves will first need to be dipped into an iron bath filled with water. At the same time, their edge should look out of the water by at least 2 cm. It is very important that the edges are clean and dry.
2. Only then can the contact from the generator be immersed in the liquid. At this very time, another contact is connected to the grounded surface and lowered into the glove. An ammeter is used as part of the test.
3. It's time to apply voltage to the electrode in the bath. The data is written off from the ammeter.

If the check is carried out correctly, then it is easy to prove the suitability of the dielectric product. Any violation can lead to an error, and subsequently an accident.

When everything is over, a protocol is drawn up. The data obtained are entered into a special journal designed to control the frequency of research.

After the test, it is necessary to dry the gloves in a room with room temperature . If this requirement is not observed, then low or high temperatures will cause damage, which, in turn, lead to the unserviceability of the product.

In some cases, an out-of-order glove test is required.

This occurs after repair work, replacement of parts of the electrical installation, or upon detection of faults. External examination of products is required.

Timing and frequency

Periodic inspection of gloves made of rubber or rubber, according to the rules, is carried out once every 6 months, this period does not take into account unscheduled tests. It does not matter whether the protective equipment was in use all this time or was in the warehouse. This test is established for rubber gloves, regardless of the extent of their use in the enterprise.

It is this approach that allows you to timely identify defects that can lead to an accident. Often it is not possible to check gloves at the factory - then third-party laboratories with a special license are involved.

Specifically, dielectric rubber gloves are only tested with electric current, although other testing methods are used for various protective equipment . During the procedure, a licensed specialist must be present who can evaluate the results obtained during the check. Almost everyone who belongs to electrical installation personnel undergoes a re-examination, in which questions are asked about the methodology and timing of testing dielectric gloves.

Remembering the information is very easy on the issue in question, since the 4-sixes rule applies here. Tests are carried out at intervals of 6 months, the voltage supplied to the product is 6 kV, the maximum permissible current rate is 6 mA, and the test duration is 60 seconds.

What if my gloves fail the test?

It also happens that the product did not pass the test at the first or second stage. That is, during an external examination or when conducting a current. It does not matter the reason why the gloves did not pass the test. If they are rejected, then they should always be treated in the same way.

On gloves, the existing stamp is crossed out with red paint. If earlier checks were not carried out, and it was not installed, then a red line is simply drawn on the product.

Such means of protection are withdrawn from operation, it is also prohibited to store them in a warehouse.

Each company where there is an electrical installation is obliged to follow special instructions. It is this document that is intended to regulate the order of subsequent actions.

The testing laboratory keeps a log where information about the results of previous tests is entered . It is called "Test log of protective equipment made of dielectric rubber and polymeric materials". There, a corresponding note is also made about the unsuitability of the pair in question. The products are disposed of at the end.

It should be understood that the presence of disposable gloves in the warehouse can cause an accident.

Human inattention often leads to sad consequences, which is why disposal is carried out immediately after the defect is identified and the relevant information is entered into the log. Each enterprise has a responsible person, whose duties include conducting timely inspections.

If repair work or replacement of structural elements was carried out at the electrical installation, then the gloves are checked for integrity on an unscheduled basis . In this way, it is possible to promptly remove unsuitable protective equipment from operation, and, accordingly, to avoid accidents.