The TV Does Not Turn On: Why Does The Indicator Blink, Click Or Blink When The LED Is Turned On? What To Do?

2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-18 12:09

Like all household appliances, the TV starts to junk from time to time, this happens regardless of the period of its use. Sometimes users are faced with the fact that the television equipment does not start, but the indicator light is on, and the relay clicks, such symptoms are usually accompanied by many other manifestations of breakdown.

Let's dwell in more detail on the reasons why the device refuses to start, and what can be done in certain situations.

Causes

The TVs presented today can be divided into several groups: liquid crystal, as well as plasma and CRT. Despite the fact that they all have noticeable differences in design, dimensions and methods of displaying a picture on the screen, the reasons that do not allow the technique to work are absolutely identical in all cases, they do not depend on the parameters of the television receiver in any way.

Depending on the cause of the breakdown and the model of the device, the way the breakdown occurs may vary slightly, but it is possible to distinguish common typical "symptoms" of malfunctions.

• When you hold down the start button directly on the TV panel or through the remote control, the indicator light stops shining evenly and blinks - this directly indicates the transition of equipment from a sleeping mode to an active working state. However, after a few seconds, at the moment when, during normal operation, the TV would have to boot up and the image would light up on the screen, it nevertheless does not work, and the LED itself either continues to blink or glows green at this moment. This suggests that the equipment did not come out of working condition and returned to its previous one - the one on duty.
• When the television equipment is launched, the image does not appear, while the equipment beeps, whistles or even clicks . We draw special attention to the fact that such suspicious sounds should come only from the case, but not from the speakers or speaker.
• If the equipment has been intensively used for many years, then periodically it starts to turn on and off .… Over time, the frequency of interruptions with switching on increases and becomes more frequent until the moment when the TV does not stop starting at all.

If the indicator light on the panel is on, it means that power is still being supplied to the control chip.

In this case, the diagnosis you need to start by checking the functionality of the remote control . Try to start work from the panel through the Power button, it is usually located in front - it should not be excluded that the cause of the error may be related to a malfunction of the remote module itself.

The reasons why the remote control stopped sending signals to the TV may be:

• oxidation of contacts;
• breakage of the infrared sensor;
• dead batteries;
• Too much dust and dirt has accumulated on the surface of the remote control microcircuit;
• some buttons are stuck and cannot be pressed;
• the remote control was poured with sweet tea or other liquid.

Usually the remote control can be repaired on your own or by contacting a specialized workshop. However, it is often cheaper to buy a new one.

If the user pressed the option to turn on the equipment on the panel, but the equipment still does not start, then most likely one of the more serious breakdowns has occurred. We will talk about them below.

External signs

Let us dwell in more detail on the external signs of a breakdown of television equipment.

Indicator is on

If the TV does not start the first time, but the LED indicator blinks, therefore, the control module tries to diagnose the nature of the error itself … As a rule, the red LED flashes a certain number of times - in this case, the user needs to take the operating manual, find the section in it with the designations of the fault categories and the options for their indication. Based on the information received and, it is already possible to take some action to rectify the situation.

Another reason, causing such an unpleasant symptom, it happens when the TV is connected to the PC as a monitor . In this situation, when the computer enters dormant mode or completely turns off, the TV, when started from the remote control, flashes the indicator for 5-10 seconds. Sometimes the TV can be the second monitor, and not the main one - in this case, you need to bring the computer out of the Stand By state, that is, simply press any key on the keyboard or just slightly move the mouse to start activation. In fact, in such a situation, the TV works, only the picture is not transmitted to it from the PC.

If the LED indicator is on, but the TV does not turn on, and at the same time you have completely ruled out the possibility of a breakdown of the remote control, then there may be various reasons for the breakdown.

Protection triggered

Usually, the TV starts up, but after a while the screen goes out, however, the equipment may not turn on at all. The most common reason for such an interruption is the lack of electricity supply to the power network. For example, this happens after a thunderstorm, lightning strike or power surges that led to the shutdown of the light while the TV was in sleep mode.

In order to fix this problem, you need to completely turn off the equipment from the network for a few minutes, and this should not be done with a button, but by unplugging the plug from the outlet . These measures will be more than enough to completely restore the functionality of television equipment in cases where the device does not turn on after an unexpected blackout in the house.

If power outages are typical for your area, then you should use an RCD or a stabilizer, and when leaving the apartment, you should completely disconnect the equipment from the outlet

Faulty processor or control. Much more complex problem. It occurs when the contacts of the TV are closed, in this case it simply stops turning on.

Keep in mind that any attempts to carry out repair work on your own most often permanently disable the equipment.

In a situation where the TV does not start from the remote control, but the indicator light does not glow red, but green or blue, the causes of the error may be interruptions in the operation of the control board. In this situation, you need to measure the voltage, and then test the correctness of the backlight power supply system.

Indicator is off

If the indicator does not light at all, then usually the reason for such a malfunction is the lack of power, if only the lamp burned out, then the TV could function in its normal mode, but only display. However, there is no need to worry before time. First, eliminate those types of problems that you can correct on your own, especially since in the overwhelming majority of cases such a problem is caused by the most primitive reason, among them the main ones can be distinguished.

Lack of current in the socket . Disconnection may occur in the system's circuit breaker, or there may be a malfunction in the outlet itself. Such a breakdown is determined using a special tester or the most standard indicator screwdriver. If there is no power, then it is necessary to inspect the machine - even when it is turned on, it is worth clicking it 2-3 times. If this did not save the situation, then the problem should be found directly in the outlet - you can do this on your own or contact the services of an electrician.

Broken extension cord . In the event that the connection to the system is carried out through it, and a direct connection to the outlet gives the correct functioning of the TV, then most likely the source of the problem is in it. If you have one, then you need to check the power button, and also the fuse - in any case, in order to fix the problem, you will need a new working device.

" Network" is disabled on the panel . Almost all types of modern TVs have such a button, if it is disabled, then you will not be able to control the TV from the remote control - you will have to manually activate the on / off option directly on the TV panel.

Wrong mode selected … The screen will dim and after a while will go into sleep mode. In order for the image to return, you need to select the "TV" option again and enjoy watching your favorite TV shows.

Failure of parts … Most often it is a capacitor or a microcircuit, less often - a power module or a control unit. Testing the functionality of television equipment units should be entrusted to specialists who have the equipment necessary for such diagnostics.

Blown fuses . This is a very urgent problem for CRT TVs. If the fuse is located in an accessible area, then anyone with minimal knowledge of technology can always remove and replace the fuse on his own.

Ways to solve the problem

If the TV unexpectedly stops starting due to failure of the matrix or backlight, then the following breakdowns may indicate this:

• multi-colored or black-and-white stripes appear on the screen;
• there is sound, but there is no picture;
• there are gray dots all over the screen - this is how broken pixels show themselves;
• when the technology is turned on, the manufacturer's logo is not displayed, only a black screen is visible.

As a rule, the matrix stops working as a result of mechanical damage.

It is simply impossible to restore a broken component; in this case, a complete replacement of the part will be required. - such repairs are extremely expensive and comparable to the purchase of new equipment.

Broken processor

All modern LCD TVs use a huge amount of all kinds of electronics in their work, which is controlled through a special module - a central processor. Any burnout of even the most insignificant hardware nodes, as well as a short circuit in it, leads to the fact that the equipment completely stops turning on. It is impossible to cope with this problem on your own, since its solution requires deep technical knowledge and skills in working with electronic microcircuits. It would be more expedient in this case to turn to the services of a master.

Firmware failure

The overwhelming majority of modern representatives of television technology support the Smart TV option. In order for the equipment to work correctly, its software needs to be updated from time to time. Interruptions in the installation of a new service pack lead to system errors that can manifest themselves in a variety of forms. One of them is the lack of starting the TV or its arbitrary reboot.

To correct this error, the module must be flashed again.

Failure of the backlit matrix. This malfunction is one of the most serious. The matrix and backlight can break even on television equipment of famous brands; in this case, the presence of sound reproduction in the absence of a picture and the ability to switch channels indicates problems. At the very first stage of a malfunction, it makes itself felt in the form of flickering dots and stripes on the screen. The only available way to restore such equipment is to replace faulty parts.

As you can see, the reasons why the TV does not turn on are very different. In some cases, ordinary users can repair equipment by turning it off for a few minutes and then turning it on again. If this minor functional failure occurs, these measures are usually sufficient. But if the cause of the breakdown is a malfunction of one or another part of the TV, then repairs will be required, which can only be carried out by the master of the service center. Unfortunately, it usually comes at a cost.