2024 Author: Beatrice Philips | [email protected]. Last modified: 2023-12-16 05:33
Stands for a motor-drill are quite a popular thing in everyday life. It is extremely useful to know how to make a stand for a manual gas drill with your own hands. Another important point is competent drawings of a homemade device.
Characteristic
Hand-held drilling equipment has gained very solid popularity. But using it "in its pure form" is very difficult and laborious. A stand for a motor-drill allows you to significantly simplify many jobs . This structure is made from a pair of metal pipes. A carriage is attached to the stationary part, which moves the drilling element.
To make the carriage move, a chain is attached to it. And this chain, respectively, is connected to a shaft equipped with an asterisk. When working, turn the handle up and down. Thus, the stand for the gas drill allows you to pull up and down the main drilling part. At the same time, and importantly, the reliability and stability of manipulation is ensured, and not only the unloading of the operator's muscles.
Adjustment of the structure is required. After all, the soil can be different, and there simply cannot be a single standard of penetration.
Moving on the ground will be greatly simplified if you equip the device with wheels.
Appointment
A manual drill for drilling holes in the ground is very useful when you need to prepare a hole for a pile or fence support. But no matter how experienced the users are, no matter how they try to do everything right, a blow to the hand will still occur. Little of, if the earth drilling attachment goes deep into the formation, over the entire auger, its extraction becomes very difficult . Homemade simplest rack effectively solves all these problems. Ascent and descent is made easier even if thick lumps of dense clay stick to the auger, all that is required is the addition of a winch to the stand.
Terms of use
Having brought the rack to the right place, you should immediately set it to the exact height by adjusting the backgauge and front legs. The tilt of the tines can be flexibly adjusted in both directions, which makes it easier to rake the soil . The first step in the work is to raise the rack, after which the drill is placed. Everything needs to be set at the hydraulic level, and then they begin to work. If the height of the rack is 2 m, then when using nozzles, you can immediately drill the ground by 1, 6 m.
If you use another nozzle on the second run, you can add 60 cm of depth . The same proportion of the depth of the first pass (80%) applies for other heights of the stanchions. You can disconnect and shake out a clogged tip without even turning off the motor. The deeper you drill, the more difficult it is to remove the tip - you just have to be prepared for this turn of events. There are no more special "tricks".
How to do it yourself?
The device is so simple that a special drawing is not needed for any trained people. The guiding elements are pipes with thin walls with a cross section of 5 cm . The length of such pipes is 1.3 m. A steel corner is suitable as a base for a homemade rack, the length of which is 0.57 m, and the size of the shelf should be 5 cm. The carriage is prepared on the basis of two-inch pipes, their length is 0.25 m …
Important: the carriage must slide freely along the guide elements . A motorized drill for drilling wells is attached to both the upper and lower segments of the carriage. In the first case, a fragment of a 20/20 profile is used, and in the second, a ¾ inch pipe cut in the longitudinal plane is used. On a square piece of rolled metal, braces obtained from a strip of steel are attached from above. This allows you to firmly fix the frame: one edge is held by a bed made of a piece of pipe and bolts, and the diagonal elements provide a grip in two additional places - also with bolts.
We can say that the carriage is put on a chain . However, the chain itself is also fixed firmly. At the point of installation, the plates are additionally tightened with M8 bolts. The first plate is welded onto the back of the carriage. The second is used to press down the chain there.
It is worth taking care of correcting the tilt of the instrument . For this purpose, take two profiles and form a jib. The angle of deflection of the rack is determined by the length of the jib. As a result, even a deviated borehole can be drilled. Moreover, to facilitate transportation, carrying the tool.
The movement of the sprocket, and then the drive shaft, is provided by a special handle . How to do it, any master can easily figure it out himself. The drive shaft can be taken from the engines of domestic motorcycles (together with the splines). A motorcycle chain can also be used, but usually it has to be extended to 2.5 m. A driven sprocket is placed on the bottom of the rack, supplemented by a bracket and an adjustment bolt. A pair of detachable paws prevents rolling over.
Recommended:
How To Make A Lawn With Your Own Hands: Styling Features (51 Photos): What Grass For Landscape Design To Plant In The Country With Your Own Hands
The emerald grassy ground in the country house is a special attribute of the beauty and comfort of a suburban area. How to make a lawn with your own hands? What features should be taken into account when laying roll material so that the lawn does not sag or deform?
Shed For Goats (37 Photos): Arrangement Of A Corral And Stall For Milking With Your Own Hands, How To Make A Shed According To A Drawing With Dimensions
Building a goat shed with your own hands is not difficult. You have to follow the rules. What could be the arrangement of a corral and stall? What is the best way to make a roof, walls, milking place with your own hands? How to make a barn according to a drawing with dimensions?
Collapsible Brazier With Your Own Hands (47 Photos): A Folding Drawing, How To Make A Folding, Prefabricated Homemade Portable Brazier For Nature
Anyone can make a collapsible brazier with their own hands, following the instructions. What features does the drawing of a folding barbecue have? How to make a folding brazier out of metal? How to calculate the dimensions of the device correctly?
Homemade Walk-behind Tractors (30 Photos): How To Make A Walk-behind Tractor With A Box From "Zhiguli" And A Rear Axle From A VAZ With Your Own Hands? How To Assemble An All-wheel Drive Device Yourself According To The Drawings At Home?
Homemade walk-behind tractors are devices that are in demand in any private household. How to make a walk-behind tractor with a box from old Zhiguli and a rear axle from a VAZ with your own hands?
Homemade Jack: How To Make A Lever Jack With Your Own Hands? Garage Lift Drawing. How To Make A Powerful PVC Pipe Jack And Other Lifting Devices?
If it is not possible to purchase a jack for lifting a car, you can always assemble a homemade unit. It is worthwhile to figure out in more detail how to make a lever jack or another type of device with your own hands, as well as what drawings of lifts for garages exist
