Garage Cladding With OSB-plates (24 Photos): Wall Decoration With Panels Inside. How To Sheathe The Ceiling With Your Own Hands? We Sheathe The Gate From The Inside With Sheets

2024 Author: Beatrice Philips | [email protected]. Last modified: 2023-12-16 05:33

There are many types of finishing work, but one of the simplest and cheapest is OSB panel finishing. With the help of this material, you can create a rather warm and cozy room, since it consists of tightly compressed wood shavings, glued together with synthetic wax and boric acid. Sheets come in different thicknesses, which vary from 6 to 25 mm, which greatly simplifies the cladding of rooms. The thinnest (6-12 mm) are fixed to the ceiling, panels from 12 to 18 mm are taken for walls, and panels from 18 to 25 mm are laid on the floor.

Pros and cons

This finishing material has a lot of advantages:

• covering the garage with OSB plates will add elegance, warmth and comfort to the room;
• when pre-painting or opening with varnish, the material does not deteriorate from moisture;
• sheets are easy to process, cut and paint, do not crumble;
• inexpensive material has soundproofing and heat-insulating properties;
• panels are resistant to fungi;
• samples labeled "Eco" or Green are absolutely safe for human health.

There are practically no downsides to this material. When protected from moisture and direct sunlight, as well as rodents, wood-based panels have virtually unlimited lifespan.

However, if you take plates without marking, they can be impregnated with formaldehyde and other toxic resins. Sewing up a room from the inside with such sheets is unhealthy.

How to sheathe the ceiling?

To sew up the ceiling with slabs, you need a frame. It can be assembled from wooden beams or metal profiles.

We calculate the number of slabs by dividing the ceiling dimensions by the standard slab size of 240x120 cm. OSB must be distributed so that there are no cross-shaped joints - this will strengthen the entire structure.

To assemble a metal box, you need to screw the wall UD-profile around the perimeter using a level, then disperse our base with an interval of 60 cm and fix it. Then we cut the CD-profile with scissors for metal or a grinder and attach it to the base using cross-shaped connectors, forming a grid of squares . For ceilings with a large area, you can use mounting U-shapes or a building corner, cut with your own hands from a CD profile and twisted with self-tapping bugs. When they are distributed inside the box, the sagging is extinguished, and the body is given greater strength.

If you assemble a box from a wooden bar, instead of a frame, special furniture corners are used.

We distribute the beams with an interval of 60 cm . The lattice is assembled in the same way, but instead of cross-shaped connectors, furniture corners are used for stitching wood. To avoid sagging of the beams, the fasteners are scattered around the perimeter of the ceiling.

At the end of the base assembly, all this is sewn up with plates with an approximate gap of 2x3 mm in order to avoid damage due to deformation from moisture or temperature drops.

Wall decoration

When decorating a room with panels, the wall frame is first assembled. The most protruding part of the wall is selected as the zero point, and the entire box is driven along it into one plane. Alignment is carried out using a level . After that, the assembly of the structure frame begins, and then everything is sewn up with chipboards.

At the end of sewing, all seams are sealed with finishing tapes to simulate a seamless connection.

The jointing tape is divided into pieces of the required size and fixed with a finishing putty at the joints . Next, you need to prime the seams, apply a thin layer of finishing putty, clean with fine-grained sandpaper to create a smooth and perfectly flat surface and paint over in several layers.

Instead of paint, you can open the walls with varnish - in this case, the surface will be reflective.

Recommendations

When working with sheets, it is worth pre-covering one side in several layers with waterproofing or varnish in order to avoid saturation of the material with moisture and its destruction. Plates are attached with the painted side to the frame; waterproofing should also be applied to the box.

Before covering the room with OSB sheets, you need to disperse and attach the wiring, preferably with a protective corrugation case in order to avoid the destruction of the wire braid from temperature and humidity changes.

To increase the thermal insulation, the frame will be filled with insulation, preferably glass wool . This will increase the heat transfer of the entire structure and protect it from destruction by rodents. All calculations should be written down in a notebook so that in the future there will be no difficulties with the installation of lighting.

At the end of the complete suturing of the garage, the gate should also be varnished so that the OSB panels do not deteriorate when open.