Washing Machine Freezes: Reasons Due To Which The Machine Freezes At The Same Time When Washing Or Draining. What To Do About The Problem?

2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-18 12:09

The washing machine can freeze immediately after switching on (for 1 minute) or during the washing or rinsing phase. What are the probable factors of such behavior of the equipment, is it possible to restore its normal operation? The cause can be either a regular problem or a serious malfunction. In this regard, it is necessary to inspect and check the mechanisms of the automatic machine.

Causes

Let's consider the simplest reasons not related to technical breakdowns. They, as a rule, are associated with the fact that the owner of the machine carried out the wrong actions. These factors include:

• drum overload with linen;
• a different washing program was selected by mistake;
• the water supply or drainage system is clogged.

How do I reset the program?

When it happened that the washing machine got stuck on rinsing or any other stage of washing, then it must be turned off and the program reset. In most machines, for their further correct functioning, it is necessary to clear the errors from the memory, which are issued in case of malfunctions. This is done differently in different machines.

1. Indesit . The program will be reset after pressing and holding the "Start" button, just wait for the panel LEDs to light up and go out. But if, when the machine hangs up, it displays an error code, only disconnecting from the outlet helps. It is not necessary to remove the problem error; it is enough to cope with the factors of its appearance. Likewise, the Indesit machine is reset to run another program if it was initially selected incorrectly.
2. Ariston … Resetting the program can be done in the same way as Indesit. These devices are from the same manufacturer and differ slightly in structure. They differ in design and program management.
3. LG . Resetting the program is quite simple, you need to press the power key or unplug it. After a new connection, the machine will easily give the opportunity to set up a new program, if it has no faults.
4. Samsung . The Samsung washing machine does not need a soft reset, you just need to turn it off in any way you like and cancel the malfunction.
5. Zanussi and Electrolux … You can cancel the program for washing machines of such models by turning on a pause or turning off the device completely. Correct reset of the error on these washing units is possible only in diagnostic mode or by connecting an electronics device to a computer.

How to stop washing?

When there is a need to turn off the washing machine during washing, you can simply press the "pause" or "on / off" button. but most machines will continue the program they interrupted after re-connecting . For such modifications, there are specialized key combinations.

On the Indesit washing machine, you can stop the washing process by pressing and holding the "start" button . Then you can set any other program. On Samsung and LG washing machines, to turn it off, you need to move the selector to a different position. On Candy, switch the program selector to zero position and wait 5-10 seconds. Then you can select another program and run it.

What to do with a breakdown?

Hanging and stopping are not always a global problem. It happens that, due to carelessness, the user has chosen the wrong washing mode, loaded the laundry incorrectly into the drum . Sometimes the drain hose is clogged or kinked. It is easy to fix such and a lot of faults on your own.

Wrong program selected

This problem is often encountered in the middle of the washing process. The machine started to work as usual: it warmed up the water, performed the prewash and main wash, and then suddenly stopped . At the same time, the door is blocked, no draining is performed. In such a situation, you need to check which program is installed. If it is a "hand" or "delicate wash", then draining and spinning is disabled automatically. It is necessary to move the mode selector to the required position and repeat the wash cycle.

In certain machines, there is an option for additional rinsing and spinning. By using this function, you can continue washing until finished.

Drum overload

Overloading creates many problems, some of which will be visible immediately, while others will show up over time. When the washing machine freezes immediately after switching on and setting the program, you should check if there are not too many items loaded into the drum . It is extremely important to create free rotation of things in the drum of the machine. In this way, you can achieve a measured distribution of powder and water, and therefore the quality of the wash.

An overloaded tank presses with impressive force on the bearings of the unit, so the machine may malfunction or break down . Before starting to operate a new machine, you need to find out from the instructions the norms and rules for loading laundry. Any machine is equipped with a special sensor that monitors the weight of the tub with linen, and does not allow starting the wash if it is overweight.

To fix the problem, you need to turn off the machine and take out some of the laundry, postponing it for another time.

Imbalance

When loading things into the machine, you should not only follow the weight norms, but also look at the even distribution of the laundry in the drum. If the machine has collected water, spun the drum several times, and does not intend to start washing, it can be assumed that there is an imbalance . Incorrect loading of laundry and other items into the unit can become a factor in the appearance of such a problem. Before washing, zippers and buttons on the items are fastened, items with Velcro are placed in specialized bags, and massive blankets, blankets and pillows are washed separately.

You can solve the problem like this:

• disconnect the machine from the mains;
• drain the water through the drain filter located at the bottom of the machine;
• open the hatch;
• disassemble things, lay the laundry evenly in the drum;
• now you can install a suitable program and start the machine again.

Clogged water supply or drainage system

When the washing machine does not switch from washing mode to rinsing mode, it can be assumed that the pipe, filter or drain pump is clogged. Waste water contains lint and threads, particles of dirt and dust, and sometimes much larger debris, for example, paper clips, pins, coins that jumped out of pockets . In order to avoid getting all this into the sewer, there is a drain filter. Over time, it becomes clogged to such an extent that it cannot pass liquid. As a result, the machine does not switch to rinse and spin mode, the wash stops.

In such a situation, you need to find where exactly the problems lie: in the car, in the drain hose or in the sewage system. It is worth checking the drain hose and straightening any kinks . It is important to exclude the option of clogging the sewer. For this purpose, the end of the drain hose must be disconnected from the sewer and sent to a bucket or bathroom. Turn on the water drain.

If it does not drain, as before, then the problem is in the unit. Otherwise it is necessary to clean the sewer pipe.

Next, you will have to remove and clean the filter located in the right corner, at the bottom of the unit. This simple exercise will bring the machine back to life . If you remove small items and debris from the pockets of clothes before washing, then the filter will need to be cleaned no more than once a year.

One of the reasons for the machine freezing is listed below.