2024 Author: Beatrice Philips | [email protected]. Last modified: 2024-01-07 13:49
The use of abutment strips for corrugated board is a very important, from a practical point of view, topic. These products are divided into upper and lower, and their sizes also differ. It is imperative to figure out how to install the abutment strips.
Appointment
The visual beauty of the profiled sheet has long been appreciated by ordinary consumers and even designers. However, not everything is as simple as it seems - in a number of places, when installing it, aesthetic problems are formed. For example, it is impossible to ensure - even with the most careful installation - that the integrity of the joints is preserved:
- with chimneys;
- pediments;
- capital walls;
- ventilation pipelines;
- antenna masts and other structures.
But integrity violation is not just a visual issue. The penetration of water from the outside negatively affects the condition of the roofing structures . It is these problems that are able to successfully solve the abutment strips for corrugated board.
In addition, they ensure the reliability of the hitching of sheets that would otherwise be pulled apart and could not be aligned. Of course, such strips are also judged by their decorative appearance.
Description of species
Outwardly, the structure looks like a metal corner. Its height is chosen arbitrarily by the developers. Experts distinguish between upper and lower planks. The latter are used mainly for passing chimney pipes or ventilation. The upper structure in this version has an almost exclusively decorative role.
But everything changes when it comes to the places where the roof is attached to the walls of the house. There, the top bar turns out to be the basic waterproofing element . It depends on it in the first place whether the under-roof space will be protected from water ingress. Sometimes it is necessary to cover a large roof area. In this case, the plank elements are placed with an overlap of at least 10 cm, and ideally even more. Such a moment should certainly be taken into account when determining the desired block sizes and their total number.
There is a universal rule that cannot be broken. It says that the tops should overlap the lower ones, not the other way around . It is this solution that guarantees the efficiency of precipitation discharge and excludes their leakage into the lower levels of the roofing cake.
You can even distinguish the lower planks from the upper ones simply by their appearance. Two edges of the corner are equipped with longitudinal bends along the entire length, which is not available in the other version.
Installation instructions
Before installing the sheets near the smoke or ventilation duct, put an inner apron. It is formed from the lower planks. Installation starts from the bottom wall of the chimney. A so-called tie is attached under this wall, allowing water to flow out. Then they do this:
- put the side parts (along the lower bar they should go with an overlap);
- they put an extension on the upper sides of the pipes - the overlap is already in relation to the side parts;
- fold the edge of the horizontal upward (this eliminates the very water seepage);
- before attaching the extensions, try them on to the wall, leaving a line along the upper edge;
- a strobe is driven along this strip, which will have to be cleaned of dust and rinsed;
- the edge of the strip is laid in the recess;
- insulate it with a sealant and press it with self-tapping screws (make sure that the vertical falls on the wall, and the horizontal - on the crate);
- carry out the installation of a profiled sheet;
- lay out the outer apron using the upper adjoining elements (with a corner without edge bends);
- attach the joints of the upper planks to the profiled sheet with rivets.
Recommended:
Cabinet Handle Profile: For Sliding Doors And Swing Doors, 10 And 16 Mm, Other Sizes, For Upper Hinged And Lower Cabinets For Chipboard, Others
Handle profile for swing wardrobes, for sliding wardrobes, what is it? Models 10 and 16 mm, what other sizes can such furniture fittings have? Profile handle manufacturers, what is the difference between the products of each individual brand?
Colors Of Corrugated Board (35 Photos): Gray Corrugated Sheet For Roof And Fence, Moss Green, White Painted Corrugated Board And Brown, Other Colors
What you need to know about the colors of the corrugated board? What is good about a gray corrugated sheet for a roof and a fence, solutions in the color of green moss? What color range should you choose, and what color standards are there?
Wall Corrugated Board: Dimensions Of The Facade Corrugated Sheet, Types And Colors, Accessories For Corrugated Board, Options For A Tree. What Is The Difference From Roofing?
What is wall sheeting? What are the usual dimensions of the facade profiled sheet, what are its typical types and colors? What accessories for the corrugated board should be used to fix it on the wall correctly?
The Dimensions Of The Corrugated Sheets For The Fence (15 Photos): The Width Of The Sheets Of The Fence Corrugated Board And The Length Standards. What Is The Size Of Corrugated Board?
What sizes of profiled sheets are used for the fence? What can be the width of the sheets of the fence corrugated board and what are the length standards? How to calculate how many sheets of corrugated board are needed for a fence?
Sizes Of Corner Kitchen Cabinets: Standard Dimensions Of Wall Cabinets. Features Of The Upper And Lower Models. Sizes Of Different Types
What is a corner kitchen cabinet? What standard dimensions and characteristics should it have for more comfortable use? This article tells about the size, location and manufacturing options of wall-mounted and floor-standing corner cabinets